Investigation of mechanical characteristics of GFRP composites produced from chopped glass fber and application of taguchi methods to turning operations

Basit Öğe Kaydı
dc.authorid0000-0003-1753-7712en_US
dc.contributor.authorÇelik, Yahya Hışman
dc.contributor.authorTürkan, Cihat
dc.date.accessioned2021-11-02T10:23:46Z
dc.date.available2021-11-02T10:23:46Z
dc.date.issued2020-04-08en_US
dc.departmentBatman Üniversitesi Mühendislik - Mimarlık Fakültesi Makine Mühendisliği Bölümüen_US
dc.description.abstractGlass fber-reinforced plastic (GFRP) composites take place in engineering materials owing to their low-weight and high-mechanical properties. In some cases, they need to be shaped by machining before using in industrial applications. However, when these composites are machined, many problems such as bad surface quality, rapid tool wear are encountered. Therefore, optimization of cutting parameters is essential to eliminate or minimize these problems. In this study, GFRP composites were produced by combining polyester matrix material with glass fbers (GF) having 6 mm, 6–12 mm, 12 mm fber length, and 20%, 25%, 30% fber ratio by weight. The tensile strengths of these composites were investigated. Turning tests were also performed with cutting speeds of 40, 80, and 120 m/min, feed rates of 0.1, 0.2 and 0.3 mm/rev, and depth of cut of 1, 2, and 3 mm, according to Taguchi L27 standard orthogonal array method. The efect of fber length and ratio, and cutting parameters on cutting forces and surface roughness were analyzed. As a result of the experiments, it was observed that the reinforced polymer matrix with GF provide to increase the tensile strength. The highest tensile strength was obtained as 55.95 MPa from the composite having a fber length of 12 mm and a fber ratio of 25%. Besides, the feed rate was determined as the most efective parameter among the all parameters on both cutting force and surface roughness. Therefore, the feed rate should be chosen low for lower cutting force and surface roughness values.en_US
dc.identifier.citationÇelik, Y.H., Türkan, C. (2020). Investigation of mechanical characteristics of GFRP composites produced from chopped glass fber and application of taguchi methods to turning operations. SN Applied Sciences, 2, pp.1-12. DOI:https://doi.org/10.1007/s42452-020-2684-5en_US
dc.identifier.endpage12en_US
dc.identifier.issn2523-3971
dc.identifier.scopusqualityQ2en|US
dc.identifier.startpage1en_US
dc.identifier.urihttps://doi.org/10.1007/s42452-020-2684-5
dc.identifier.urihttps://hdl.handle.net/20.500.12402/3873
dc.identifier.volume2en_US
dc.language.isoenen_US
dc.publisherSpringerLinken_US
dc.relation.isversionof10.1007/s42452-020-2684-5en_US
dc.relation.journalSN Applied Sciencesen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - İdari Personel ve Öğrencien_US
dc.rightsinfo:eu-repo/semantics/openAccessen_US
dc.rightsAttribution-NonCommercial-ShareAlike 3.0 United States*
dc.rights.urihttp://creativecommons.org/licenses/by-nc-sa/3.0/us/*
dc.subjectCutting Forceen_US
dc.subjectGFRP Compositeen_US
dc.subjectTaguchien_US
dc.subjectTensile Strengthen_US
dc.subjectTurningen_US
dc.subjectSurface Roughnessen_US
dc.titleInvestigation of mechanical characteristics of GFRP composites produced from chopped glass fber and application of taguchi methods to turning operationsen_US
dc.title.alternativeGFRP kompozitlerinin mekanik özelliklerinin araştırılması kıyılmış cam fberden üretilmiştir ve taguchi uygulaması tornalama işlemleri için yöntemleren_US
dc.typeArticleen_US

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim
İsim:
Investigation of mechanical characteristics of GFRP composites.pdf
Boyut:
2.26 MB
Biçim:
Adobe Portable Document Format
Açıklama:
Tam Metin / Full Text
İndir
Lisans paketi
Listeleniyor 1 - 1 / 1
Küçük Resim Yok
İsim:
license.txt
Boyut:
1.44 KB
Biçim:
Item-specific license agreed upon to submission
Açıklama:
İndir

Koleksiyon

Mühendislik-Mimarlık Fakültesi Makine Mühendisliği Bölümü Makale Koleksiyonu