Investigation of cutting parameters affecting on tool wear and surface roughness in dry turning of Ti-6Al-4V using CVD and PVD coated tools

Basit Öğe Kaydı
dc.authorid0000-0003-1753-7712en_US
dc.contributor.authorÇelik, Yahya Hışman
dc.contributor.authorKılıçkap, Erol
dc.contributor.authorGüney, Musa
dc.date.accessioned2019-06-27T05:47:56Z
dc.date.available2019-06-27T05:47:56Z
dc.date.issued2017-06-01en_US
dc.departmentBatman Üniversitesi Mühendislik - Mimarlık Fakültesi Makine Mühendisliği Bölümüen_US
dc.description.abstractThere are some problems in the machining of titanium alloys with excellent properties such as high strength, good corrosion resistance, long service life and low weight. The leading problem appears to be the fast tool wear and the bad machining surface. Therefore, in this study, it was investigated whether cutting parameters have effect on tool wear and surface roughness by turning under dry cutting condition of Ti-6Al-4V alloy with excellent properties. CVD (TiCN + Al2O3 + TiN) and PVD (TiAlN) coated WC tools were used in the experiments. Then the Ti-6Al-4V alloy turned with the combinations of the different cutting speed, feed rate, cutting long and depth of cut. We observed that the tools wear in both CVD and PVD coated WC tools increased with increasing the cutting speed, feed rate, depth of cut and cutting length. However, while tools wear increased with increasing cutting speed, the surface roughness reduced to an optimum level. Especially, the surface roughness was worsened above the optimum level changing with increasing the feed rate, cutting length and depth of cut. The tool wear with PVD coated WC tools was observed to be less than the CVD coated WC tools. However, the values of the surface roughness obtained with PVD coated WC tools with increase in depth of cut, feed rate and cutting length has given us higher values when compared to CVD coated WC tools.en_US
dc.identifier.citationÇelik, Y. H., Kılıçkap, E., Güney, M. (2016). Investigation of cutting parameters affecting on tool wear and surface roughness in dry turning of Ti-6Al-4V using CVD and PVD coated tools. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 39(6), pp. 2085-2093. https://doi.org/10.1007/s40430-016-0607-6en_US
dc.identifier.endpage2093en_US
dc.identifier.issn1678-5878
dc.identifier.issn1806-3691
dc.identifier.issue6en_US
dc.identifier.scopusqualityQ2en_US
dc.identifier.startpage2085en_US
dc.identifier.urihttps://doi.org/10.1007/s40430-016-0607-6
dc.identifier.urihttps://hdl.handle.net/20.500.12402/2141
dc.identifier.volume39en_US
dc.identifier.wosqualityQ2en_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherSpringer Natureen_US
dc.relation.isversionof10.1007/s40430-016-0607-6en_US
dc.relation.journalJournal of the Brazilian Society of Mechanical Sciences and Engineeringen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.rightsAttribution-NonCommercial-ShareAlike 3.0 United States*
dc.rights.urihttp://creativecommons.org/licenses/by-nc-sa/3.0/us/*
dc.subjectWearen_US
dc.subjectRoughnessen_US
dc.subjectTurningen_US
dc.subjectTitaniumen_US
dc.titleInvestigation of cutting parameters affecting on tool wear and surface roughness in dry turning of Ti-6Al-4V using CVD and PVD coated toolsen_US
dc.typeArticleen_US

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
Küçük Resim Yok
İsim:
Çelik2017_Article_InvestigationOfCuttingParamete.pdf
Boyut:
4.37 MB
Biçim:
Adobe Portable Document Format
Açıklama:
Tam Metin / Full Text
İndir
Lisans paketi
Listeleniyor 1 - 1 / 1
Küçük Resim Yok
İsim:
license.txt
Boyut:
1.44 KB
Biçim:
Item-specific license agreed upon to submission
Açıklama:
İndir

Koleksiyon

Mühendislik-Mimarlık Fakültesi Makine Mühendisliği Bölümü Makale Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu
WoS İndeksli Yayınlar Koleksiyonu