11 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 10 / 11
Öğe Çok katmanlı duvar ve çatı tiplerinin ısıl ve fiziksel özelliklerinin dinamik ısıl karakterlerine olan etkisinin incelenmesi(Muğla Sıtkı Koçman Üniversitesi, 2015) Oktay, Hasan; Budak Ziyadanoğulları, Neşe; Argunhan, Zeki; Yumrutaş, Recep; Işık, Mehmet ZerrakkiÖğe Dimension and insulation thickness optimization of circular flat plate solar collectors(Energy Education Science and Technology, 2011) Argunhan, ZekiIn this study, expressions for optimum radius of a circular flat plate solar collector and the optimum insulation thickness distribution are derived by using the concept of solar gain, which maximizes the life-cycle savings. For the specified condition the optimum radius has been found as 2.14 m and the optimum insulation thickness distribution on back of collectors has been formulized. The insulation material thickness distribution has been determined by performing a detailed dimensional analysis; therefore heat loss is minimized, and results are presented in graphics.Öğe Second Law analysis in concentric heat exchangers with vortex flow generators(Energy Education Science and Technology, 2011) Argunhan, Zeki; Çakmak, Gülşah; Yıldız, Cengiz; Behçet, RasimIn the present study, the experimental results of heat transfer of a concentric tube heat exchanger were analyzed with respect to Second Law of Thermodynamics to reach the geometric optimal design of the heat exchangers. In order to increase the heat transfer, the vortex generators were placed in the entrance of the inner pipe of the heat exchanger. These vortex generators are 60 mm in diameter having six angled (55°, 65°, 75°, 90°) winglets. The winglets have one rectangular slot in each and are 2×7 mm in dimensions. Experiments were carried out with different Reynolds Numbers. Air as hot fluid and water as cold fluid were passed through the inner pipe and outer pipe of the concentric tube heat exchanger, respectively. The variations of the efficiency and Entropy Generation Number with respect to Reynolds Number are shown in graphics, and the results were discussed.Öğe Investigation of indoor air quality in Batman University of central and West Raman Campus classrooms(Kilis 7 Aralık Üniversitesi, 2016) Argunhan, Zeki; Avcı, Ali SerkanÖğe The effect of rotary type turbulator placed in entrance of heat exchanger on heat transfer and frictional loss(Energy Education Science and Technology, 2011) Argunhan, Zeki; Behçet, Rasim; Yakut, Ali KemalIn this study, improving heat transfer in heat exchangers with paralel flow is gained by using swirl flow. For this purpose, a propeller type of turbulator was placed in the entrance of interior pipe of heat exchanger with paralel flow and the effect of turbulator on the heat transfer and friction losses in steady conditions was experimentally investigated. The effect of production of turbulance for improvement of heat transfer in interior pipe flows and the effects of turbulator on heat transfer and pressure drop are experimentally researched by placing a propeller type of turbulator at the entrance of heat exchanger to produce swirl air flow. In experiment setup, water was used as the fluid on which the heat was transferred and air was used as the fluid from which heat was transferred to the water. By usage of datas obtained from experimental measurements were calculated for Reynolds number ranging from 8000 to 24000 necessary relationships effet on heat transfer and pressure drop. In comparison with empty pipe it was seen that the heat transfer increased at range between 25,5%- 50,3% and the friction losses increased 5 times. Besides, by analyzing the system exergy, the dependence of non-dimensional exergy loss on Reynolds number was drawn to investigate whether this improvement technique is advantageous thermodynamically or not. When comparing the exergy losses in empty pipe and the pipe with a turbulator at approximately same Reynolds numbers, it was seen that exergy loss is 15% higher for empty pipe than that for the pipe with the turbulator. As a result of that information, the improvement technique was proved to be advantageous in thermodynamic manner too. By the usage of turbulator that results in the partial recovery of loss energy, it was proven that the improvement technique was thermodynamically advantageousÖğe Effect of swirl generators with different sized propeller on heat transfer enhancement(Energy Education Science and Technology, 2011) Argunhan, Zeki; Yıldız, Cengiz; Çakmak, GülşahIn this study, the swirl flow that is one of the passive methods is used for increasing the heat transfer coefficient in the concentric heat exchangers. For this purpose, propeller type swirl generators were prepared to test in the experiments. So, the effect of propellers placed in the inner pipe of the concentric heat exchangers on the heat transfer and pressure drop was investigated experimentally. Experiments were undertaken for the Reynolds Number range of 4000-12000 and for both parallel and counter-flow. It is shown that, the propellers rotated freely with the effect of fluid flowed in the inner pipe are swirling flow generator and they have improved heat transfer. In addition that up to 50% enhancements could be accomplished in heat transfer rates with the swirl generators compared to without the swirl generators. In the parallel flow mode, the enhancement was 10% lower than that of counter-flow at the same Reynolds number. On the other hand the pressure losses increase approximately 3 times more than the empty tube related to Reynolds numbers and propeller sizes. As an outcome of the study, the results showed that a rather smaller size but the same capacity heat exchanger could be proposed by using these elements imposing swirling to the fluid flowing through inner pipe.Öğe Estimation of thermal performances of newly produced lightweight walls for energy efficient buildings(Kilis 7 Aralık Üniversitesi, 2016) Oktay, Hasan; Yumrutaş, Recep; Argunhan, Zeki; Ayanoğlu, AbdulkadirÖğe Experimental investigations on thermophysical properties of concrete produced from different aggregates(Türk Tesisat Mühendisleri Derneği, 2014) Oktay, Hasan; Argunhan, Zeki; Yumrutaş, RecepÖğe Design of solar cathodic protection system in Batman(Kilis 7 Aralık Üniversitesi, 2016) Argunhan, Zeki; Reşitoğlu, Mehmet SelimÖğe Türkiye’de yaygın olarak kullanılan duvar ve çatı tiplerinin ısıl kazançlarının Batman ili için incelenmesi(Batman Üniversitesi, 2018) Oktay, Hasan; Argunhan, Zeki; Ayanoğlu, Abdulkadir
