7 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 7 / 7
Öğe Exhaust emissions of a CI engine operated with biodiesel from rapeseed oil(Taylor & Francis, 2011-01-16) Aydın, Hüseyin; İlkılıç, CumaliIn this study, biodiesel was produced from rapeseed oil and was used in a single cylinder, naturally aspirated and direct-injected diesel engine as pure biodiesel (B100) and as a blend with standard diesel fuel by 20% biodiesel to 80% diesel fuel (B20). The diesel engine emissions and some performance parameters were investigated at fully loaded engine conditions. The effects of pure biodiesel and its blend with diesel fuel on emissions of carbon monoxide (CO), nitrogen oxides (NOx), carbon dioxide (CO2), and sulfur dioxide (SO2) were clarified. Results showed that biodiesel fuel is environmentally friendly since it reduced the emissions of CO, SO 2, and CO2 of engines at all speeds. Results also indicated that the pure biodiesel gave about 12% lower power and 20 to 25% higher fuel consumption as compared to diesel. However, the results were almost the same or slightly different from a blend of biodiesel-diesel and petroleum diesel fuel.Öğe The harmful effects of diesel engine exhaust emissions(Taylor & Francis, 2012-03-16) İlkılıç, Cumali; Aydın, HüseyinWith the increase in the number of engine vehicles, air pollution is also increasing quickly; and with the increase in air pollution, all living conditions are affected in a negative way. Diesel engines also cause air pollution, which adversely affects human health and is becoming a permanent problem. A single-cylinder diesel engine was used in this work; the exhaust gas emissions, in different speed ranges, were investigated. These emissions are carbon monoxide emissions (CO), nitrogen oxides (NO x), oxygen (O 2), and carbon dioxide (CO 2). The amount of the changes in emissions was evaluated in terms of air pollution with graphics.Öğe Effects of thermal barrier coating on the performance and combustion characteristics of a diesel engine fueled with biodiesel produced from waste frying cottonseed oil and ultra-low sulfur diesel(Taylor & Francis, 2016-09-01) Aydın, Selman; Sayın, Cenk; Altun, Şehmus; Aydın, HüseyinIn this study, the top surfaces of piston and valves of a four-strokes and direct-injection diesel engine have been coated—with no change in the compression ratio—with a 100 μm of NiCrAl lining layer via plasma spray method and this layer has later been coated with main coating material with a mixture of 88% of ZrO 2 , 4% of MgO and 8% of Al 2 O 3 (400 μm). Then, after the engine-coating process, ultra-low sulfur diesel (ULSD) as base fuels and its blend with used frying cottonseed oil derived biodiesel in proportion of 20%, volumetrically, have been tested in the coated engine and data of combustion and performance characteristics on full load and at different speeds have been noted. The results, which were compared with those obtained by uncoated-engine operation, showed that thermal efficiency increased, and engine noise reduced. Cylinder gas pressure values obtained from the diesel engine which has been coated with thermal barriers have been found to be somewhat higher than those of the uncoated-engine. Also, maximum pressure values measured in both engines and under the same experimental conditions through the use of test fuel have been obtained after TDC. Moreover, heat release rate and heat release have occurred earlier in the coated-engine. NOx emissions were increased while CO and HC emissions were remained almost the same with a little bit decrease.Öğe Emissions from an engine fueled with biodiesel-kerosene blends(Taylor & Francis, 2011-01) Aydın, Hüseyin; Bayındır, Hasan; İlkılıç, CumaliBiofuels are renewable energy sources for internal combustion engines and they have low emissions. They are increasingly used as an alternative to petroleum fuels. In this work, three different fuel types, such as commercial diesel fuel (D2), 20% biodiesel and 80% diesel fuel called here as B20, and 80% biodiesel and 20% kerosene, called here as BK20, were used in a single cylinder, four stroke, direct injection compression ignition engine. Kerosene was used as an additive to approach the properties of biodiesel to D2. The effects of the blends on CO, NOx, and smoke emissions as well as on some of the performance parameter of the engine were investigated. The prepared fuel, BK20 blend, has almost the same fuel properties as conventional diesel fuel. The experimental results showed that the exhaust emissions for BK20 were fairly reduced as compared to diesel fuel as well as B20. Besides, the performance of CI engine was improved with the use of the BK20, especially in comparison to B20. Results suggest that the BK20 can be substituted to the petroleum-based diesel fuel in diesel engines.Öğe The effects of λ and ε on engine performance and exhaust emissions using ethanol-unleaded gasoline blends in an SI engine(Taylor & Francis, 2011-01) Bayındır, Hasan; Yücesu, Hüseyin Serdar; Aydın, HüseyinIn this study, the effect of relative air-fuel ratio (λ) and compression ratio (ε) on engine performance and exhaust emissions was experimentally investigated. The experiments were performed by varying ethanol-unleaded gasoline blends as E0 (100% unleaded gasoline), E10 (10% ethanol and 90% gasoline blend), E30 (30% ethanol and 70% gasoline blend), and E85 (85% ethanol and 15% gasoline blend). In experiments, first the effects of ethanol-unleaded gasoline blends on engine performance and exhaust emissions at 0.931, 1, and 1.069 λ values were clarified. Second, tests were carried out with compression ratios of 7:1, 9:1, and 11:1. The results indicated that the relative air-fuel ratio and ethanol content play an important role in reducing CO (carbon monoxide emissions) and HC (hydrocarbon) emissions. Results also showed that the engine power was slightly decreased, especially at higher engine speeds. A probable knocking phenomenon did not occur with the increase of compression ratio because of a higher octane number of ethanol-unleaded gasoline blends.Öğe An experimental study on the exhaust emissions of a partially loaded compressed ignition engine fueled with biodiesel derived from cottonseed oil(Taylor & Francis, 2010-01) Aydın, Hüseyin; Bayındır, HasanThe world energy demand is increasing rapidly due to the excessive use of the fuels but because of limited reserves, the researchers are now looking for alternative fuels. Another serious problem associated with the use of petroleum fuel is the increase in pollutants emissions. In this study, cottonseed oil methyl ester was added to diesel fuel by volume of 5% (B5), 20% (B20), and 50% (B50). Blends were used in a single cylinder, direct injection, air-cooled diesel engine at partial and full load condition. In experiments, the effects of cottonseed oil methyl ester ester-diesel fuel blend on the engine fuel consumption and exhaust emissions were investigated at 2,000 rpm of engine speed that most engines run on. At the tests, the effect of blends on fuel consumption, exhaust gases temperature, CO, NOx, SO2, and smoke opacity was clarified. The experimental results showed that cottonseed oil methyl ester can be substituted for the diesel fuel without any modifications in diesel engines.Öğe Combustion, performance, and emissions of safflower biodiesel with dimethyl ether addition in a power generator diesel engine(Taylor & Francis, 2020-04-29) Aydın, Hüseyin; Işık, Mehmet Zerrakki; İşcan, Bahattin; Topkaya, HüsnaIn this study, the effect of dimethyl ether (DME) addition to diesel (ultralow sulfur diesel fuel) and biodiesel fuels on the combustion, performance, and emissions of a diesel-powered generator was investigated. For this purpose, fuel samples of the ternary blend that volumetrically composed of 10% safflower biodiesel–10% dimethyl ether–80% ultralow sulfur diesel fuel (B10DME10), the ternary blend that volumetrically composed of 25% safflower biodiesel–25% dimethyl ether–50% ultralow sulfur diesel fuel (B25DME25), the binary blend that volumetrically composed of 25% safflower biodiesel–75% ultralow sulfur diesel fuel (B10DME10) B25, and pure safflower oil biodiesel (B100) and standard ultralow sulfur diesel (D2) were prepared. The test engine was loaded by power drawing from the generator by the usage of equivalent powered electrical heating resistances. Generally, using DME with biodiesel improved the combustion properties of biodiesel blends that can be attributed to the lower viscosity of DME. The maximum cylinder pressure was obtained for B10DME10 in general and sometimes for B25DME25. When test fuels are compared, DME blends showed higher and earlier peaks of heat release compared to diesel and biodiesel blend fuels especially. It was found that combustion is more efficient from mass fuel consumption (MFC) and brake specific fuel consumption (BSFC) values in the use of DME than biodiesel. BSEC values of using DME in the blends considerably decreased that it is the proof of improved combustion and energy efficiency. The highest average efficiency values were obtained for B25DME25 as 28.3% although it has a lower calorific value than D2 due to the considerably improved combustion properties of DME, while the average efficiency values were 23.1%, 23.3%, and 20.7% for D2, B25, and B100 fuels, respectively. Highest carbon monoxide (CO) emissions were obtained in the use of pure biodiesel, while the lowest CO emissions were obtained in the use of DME. The addition of DME is seen to increase the nitrogen oxides (NOx) and CO emissions.
