3 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 3 / 3
Öğe Milling Inconel 718 workpiece with cryogenically treated and untreated cutting tools(SpringerLink, 2021-07-17) Gürbüz, Hüseyin; Baday, ŞehmusAlthough Inconel 718 is an important material for modern aircraft and aerospace, it is a kind material, which is known to have low machinability. Especially, while these types of materials are machined, high cutting temperatures, BUE on cutting tool, high cutting forces, and work hardening occur. Therefore, in recent years, instead of producing new cutting tools that can withstand these difficult conditions, cryogenic process, which is a heat treatment method to increase the wear resistance and hardness of the cutting tool, has been applied. In this experimental study, feed force, surface roughness, vibration, cutting tool wear, hardness, and abrasive wear values that occurred as a result of milling of Inconel 718 material by means of cryogenically treated and untreated cutting tools were investigated. Three different cutting speeds (35-45-55 m/min) and three different feed rates (0.02- 0.03-0.04 mm/tooth) at constant depth of cut (0.2 mm) were used as cutting parameters in the experiments. As a result of the experiments, lower feed forces, surface roughness, vibration, and cutting tool wear were obtained with cryogenically treated cutting tools. As the feed rate and cutting speed were increased, it was seen that surface roughness, vibration, and feed force values increased. At the end of the experiments, it was established that there was a significant relation between vibration and surface roughness. However, there appeared an inverse proportion between abrasive wear and hardness values. While BUE did not occur during cryogenically treated cutting tools, it was observed that BUE occurred in cutting tools which were not cryogenically treated. Also, in this study, the statistical validity of the experimental values was tested with the help of secondorder equations and analyses of variance (ANOVA). R2 values obtained as 99.14%, 99.76%, and 97.98% for vibration, surface roughness, and feed force values were modeled statistically with the help of second-order equations, respectively.Öğe Analysis of spheroidized AISI 1050 steel in terms of cutting forces and surface quality(Slovenska Akademia Vied, 2016) Baday, Şehmus; Başak, Hüdayim; Güral, AhmetIn this study, the effects of microstructure differences obtained with the application of different spheroidizing heat treatment cycles on medium carbon steel on cutting forces and surface roughness values were investigated. For this purpose, a group of AISI 1050 materials was annealed at 700°C below Ac1 temperature for 720 min and cementite phases were spheroidized by the traditional method. Another group of materials was quenched after austenitization at 850°C for 15 min and then cementites were spheroidized in the ferrite matrix by over-tempering separately at 600°C for 15 and 60 min and at 700°C for 60 min. Machining of the samples was tested under dry cutting conditions in CNC turning center with SNMG 120408 cementite carbide cutting tool and proper PSBNR 2525M12 tool holder with 75-degree edge angle. Cutting forces of traditionally spheroidized samples were lower than the samples spheroidized after quenching. In addition, their cutting forces decreased due to the increase in the average sizes of spheroidal cementite. Minimum surface roughness value was obtained from the samples which were spheroidized at 600°C for 15 min after quenching. However, surface roughness rate of the sample increased as spheroidizing time increased.Öğe Effect of MQL flow rate on machinability of AISI 4140 steel(Taylor & Francis, 2020-06-27) Gürbüz, Hüseyin; Gönülaçar, Yunus Emre; Baday, ŞehmusMany studies were performed about the influence of minimum quantity lubrication (MQL) technique on cutting performance in the literature, but there is no paper examining the effect of different MQL flow rates and cutting parameters on machinability of AISI 4140 material as a whole. In this study, the effects of different MQL flow rates and cutting parameters on surface roughness, main cutting force and cutting tool flank wear (VB), with great importance among the machinability criteria, and forming as a result of the machining of AISI 4140, were revealed. At the end of the experiments, it was determined that rise of flow rate affected main cutting forces positively to a certain extent; yet, it exhibited no significant effect on surface roughness, but reduced VB. Also, it was observed that both main cutting force and surface roughness increased with the increase of feed, while generally decreased with the increase of cutting speed. It was seen that flank wear was positively affected by the increase in flow rate; and this decreased with the increase in flow rate. R2 values obtained as 99.8% and 99.9% for main cutting forces and surface roughness values modeled statistically with the help of quadratic equations, respectively.
