2 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 2 / 2
Öğe The effect of n-butanol additive on low load combustion, performance and emissions of biodiesel-diesel blend in a heavy duty diesel power generator(Elsevier, 2017-04) Işık, Mehmet Zerrakki; Bayındır, Hasan; İşcan, Bahattin; Aydın, HüseyinDiesel power generators are often used under partially load conditions. Especially, under low load conditions, it is crucial to find a solution for their considerably high brake specific fuel consumption (bsfc) and exhaust output emissions. Other points are the usability of waste cooking oil and an oxygenated alternative fuel in low load conditions of diesel generator. In this point of view, 10% n-butanol and 10% biodiesel mixture was blended with 80% of ultra low sulfur diesel fuel named here as BB20 was used and comparisons have been made with 20% biodiesel/80% diesel fuel named here as B20 and ultra low sulfur diesel fuel named here as (D2). Previously, main important physical and chemical fuel properties of test fuel have been found. These fuels were tested in low load operations of a diesel engine generator in order to find out the effects of blend fuels on combustion characteristics, performance and emissions of the test engine. The test results are presented in this paper and seem to raise quite interesting points. Butanol addition to diesel and biodiesel blends can be considered as a good solution for reducing density, viscosity and thus sustainable usability of biodiesel and increase thermal efficiency and lower carbon monoxide (CO) and oxides of nitrogen (NOx) under comparatively lower load conditions in diesel power generator engines.Öğe Combustion, performance, and emissions of safflower biodiesel with dimethyl ether addition in a power generator diesel engine(Taylor & Francis, 2020-04-29) Aydın, Hüseyin; Işık, Mehmet Zerrakki; İşcan, Bahattin; Topkaya, HüsnaIn this study, the effect of dimethyl ether (DME) addition to diesel (ultralow sulfur diesel fuel) and biodiesel fuels on the combustion, performance, and emissions of a diesel-powered generator was investigated. For this purpose, fuel samples of the ternary blend that volumetrically composed of 10% safflower biodiesel–10% dimethyl ether–80% ultralow sulfur diesel fuel (B10DME10), the ternary blend that volumetrically composed of 25% safflower biodiesel–25% dimethyl ether–50% ultralow sulfur diesel fuel (B25DME25), the binary blend that volumetrically composed of 25% safflower biodiesel–75% ultralow sulfur diesel fuel (B10DME10) B25, and pure safflower oil biodiesel (B100) and standard ultralow sulfur diesel (D2) were prepared. The test engine was loaded by power drawing from the generator by the usage of equivalent powered electrical heating resistances. Generally, using DME with biodiesel improved the combustion properties of biodiesel blends that can be attributed to the lower viscosity of DME. The maximum cylinder pressure was obtained for B10DME10 in general and sometimes for B25DME25. When test fuels are compared, DME blends showed higher and earlier peaks of heat release compared to diesel and biodiesel blend fuels especially. It was found that combustion is more efficient from mass fuel consumption (MFC) and brake specific fuel consumption (BSFC) values in the use of DME than biodiesel. BSEC values of using DME in the blends considerably decreased that it is the proof of improved combustion and energy efficiency. The highest average efficiency values were obtained for B25DME25 as 28.3% although it has a lower calorific value than D2 due to the considerably improved combustion properties of DME, while the average efficiency values were 23.1%, 23.3%, and 20.7% for D2, B25, and B100 fuels, respectively. Highest carbon monoxide (CO) emissions were obtained in the use of pure biodiesel, while the lowest CO emissions were obtained in the use of DME. The addition of DME is seen to increase the nitrogen oxides (NOx) and CO emissions.
