Arama Sonuçları
Listeleniyor 1 - 10 / 467
Öğe Otomotiv fren balatalarının sürtünme performansında sic etkisi(Uludağ Üniversitesi, 2012-06) Altun, Şehmus; Öner, Cengiz; Sugözü, İlkerBu çalışmada, yüksek mukavemet, düşük aşınma, daha fazla yük ve sıcaklık dayanımı özelliklerine sahip SiC içeren balata numunelerinin sürtünme katsayısı ve aşınma dayanımına etkisi incelenmiştir. Balata bileşeni içerisine %5, %10 ve %15 SiC ilave edilmiştir. Sonuç olarak, SiC oranı arttıkça aşınma direnci artmış ve sürtünme katsayısı azalmıştırÖğe Investigation of plasma arc cutting parameters with type-2 fuzzy set and system(De Gruyter, 2013-10) Çelik, Yahya Hışman; Özek, Cebeli; Bulut Özek, MüzeyyenThe objective of the present study was it to design a type-2 fuzzy set and system in order to predict surface roughness and hardness depending on the parameters (material thickness, cutting speed, arc voltage and current) of the plasma arc cutting process of S235JR sheet materials. Therefore, some experimental studies were conducted. The experimentally determined data were used to describe the type-2 fuzzy set and system. Type-2 fuzzy set and system was found to be usefull to predict surface roughnes and hardness. According to the obtained values, the best surface roughness and the values closest to the hardness of the raw material were obtained at 1500 mm/min cutting speed, 8 mm material thickness, 115 V arc voltage and 80 A current.Öğe Biodiesel production from inedible animal tallow and an experimental investigation of its use as alternative fuel in a direct injection diesel engine(Elsevier, 2009-02-15) Altun, Şehmus; Öner, CengizIn this study, a substitute fuel for diesel engines was produced from inedible animal tallow and its usability was investigated as pure biodiesel and its blends with petroleum diesel fuel in a diesel engine. Tallow methyl ester as biodiesel fuel was prepared by base-catalyzed transesterification of the fat with methanol in the presence of NaOH as catalyst. Fuel properties of methyl ester, diesel fuel and blends of them (5%, 20% and 50% by volume) were determined. Viscosity and density of fatty acid methyl ester have been found to meet ASTM D6751 and EN 14214 specifications. Viscosity and density of tallow methyl esters are found to be very close to that of diesel. The calorific value of biodiesel is found to be slightly lower than that of diesel. An experimental study was carried out in order to investigate of its usability as alternative fuel of tallow methyl ester in a direct injection diesel engine. It was observed that the addition of biodiesel to the diesel fuel decreases the effective efficiency of engine and increases the specific fuel consumption. This is due to the lower heating value of biodiesel compared to diesel fuel. However, the effective engine power was comparable by biodiesel compared with diesel fuel. Emissions of carbon monoxide (CO), oxides of nitrogen (NOx), sulphur dioxide (SO2) and smoke opacity were reduced around 15%, 38.5%, 72.7% and 56.8%, respectively, in case of tallow methyl esters (B100) compared to diesel fuel. Besides, the lowest CO, NOx emissions and the highest exhaust temperature were obtained for B20 among all other fuels. The reductions in exhaust emissions made tallow methyl esters and its blends, especially B20 a suitable alternative fuel for diesel and thus could help in controlling air pollution. Based on this study, animal tallow methyl esters and its blends with petroleum diesel fuel can be used a substitute for diesel in direct injection diesel engines without any engine modification.Öğe Effects of cutting parameters and point angle on thrust force and delamination in drilling of CFRP(De Gruyter, 2014-11-14) Çelik, Yahya Hışman; Kılıçkap, Erol; Yardımeden, AhmetParts made of composite materials are generally produced by near-net-shape technology. However, additional machining operations such as drilling are often required to facilitate components assembling. Drilling of composite materials is also a common process in the assembly of aerospace and automotive composite structures. During drilling, unlike the conventional materials, a few damage forms may take place. Among these damage forms, the delamination is the most important one. Therefore, the experimental studies carried out on drilling of CFRP composite materials for determining optimum processing parameters are of great importance. In this particular study, delamination in CFRP composites caused by drilling was investigated. The composite material was drilled under various spindle speeds, feed rates and drill point angles. The results showed that delamination and thrust forces were affected by cutting parameters. It was demonstrated that feed rate and drill point angle make the largest contribution to the overall performance.Öğe Doğal fiber takviyeli kompozitler üzerine bir derleme çalışması(IESS Publishing, 2019-06) Çelik, Yahya Hışman; Yalçın, RojinÖğe An exergy analysis of a concentric tube heat exchanger using hBN-water nanofluids(Inder Science Publishers, 2021) Budak Ziyadanoğulları, Neşe; Perçin, SüleymanThis study investigated the effects of using nanofluids prepared with hexagonal boron nitride (hBN) nanoparticles on the thermal performance and pressure drop of a concentric tube heat exchanger. Experiments were carried out with water-hBN nanofluids for stable, dispersed, 0.01%, 0.1% and 1% volume concentrations, at different flow rates and Reynolds numbers under parallel and counter-flow conditions. When the experimental results were examined, the exergy loss was higher in the parallel-flow heat exchanger compared to the counter-flow heat exchanger. The highest exergy loss value was obtained for distilled water at the highest Reynolds number (Re = 8,700) for parallel flow operation at 170 W. The exergy loss of water at the highest Reynolds number (Re = 8,700) for parallel flow operation increased by 15.7%, 24.8% and 49.8% for hBN-water concentrations of 0.01%, 0.1% and 1%, respectively. Exergy loss of water at the highest Reynold number (Re = 8,700) for counter flow operation increased by 11.3%, 17.3% and 29.2% for hBN-water concentrations of 0.01%, 0.1% and 1%, respectively. When evaluating the exergy analysis of the system, exergy losses due to pressure drops were negligible for both flows (parallel and counter).Öğe Uluslararası Mühendislik, Doğa ve Sosyal Bilimler Sempozyumu (ISENS-21): Bildiri tam metin kitabı 25-28 Kasım 2021(Batman Üniversitesi, 2021) Demir, İdris; Aydın, HüseyinÖğe The comparison of engine performance and exhaust emission characteristics of sesame oil-diesel fuel mixture with diesel fuel in a direct injection diesel engine(Elsevier, 2008-01-09) Altun, Şehmus; Bulut, Hüsamettin; Öner, CengizThe use of vegetable oils as a fuel in diesel engines causes some problems due to their high viscosity compared with conventional diesel fuel. Various techniques and methods are used to solve the problems resulting from high viscosity. One of these techniques is fuel blending. In this study, a blend of 50% sesame oil and 50% diesel fuel was used as an alternative fuel in a direct injection diesel engine. Engine performance and exhaust emissions were investigated and compared with the ordinary diesel fuel in a diesel engine. The experimental results show that the engine power and torque of the mixture of sesame oil-diesel fuel are close to the values obtained from diesel fuel and the amounts of exhaust emissions are lower than those of diesel fuel. Hence, it is seen that blend of sesame oil and diesel fuel can be used as an alternative fuel successfully in a diesel engine without any modification and also it is an environmental friendly fuel in terms of emission parameters.Öğe Effect of tightening torque on the fatigue strength of bolted composite lap joints(Kilis 7 Aralık Üniversitesi, 2016) Topkaya, Tolga; Solmaz, Murat YavuzÖğe Şanlıurfa ilinde yatay yüzeye gelen anlık global güneş ışınımının modellenmesi(Dicle Üniversitesi, 2019-03-15) Karakaya, Hakan; Kallioğlu, Mehmet Ali; Avcı, Ali Serkan; Ercan, UmutBu çalışma ile Şanlıurfa ilinin iklim özellikleri ve topografik yapısı göz önüne alınarak yatay düzleme gelen aylık ortalama günlük global güneş radyasyonunun tespit edilebilmesi için literatürde yer alan 5 farklı model incelenmiştir. Sonuçlar istatistiksel karşılaştırma metotları, belirlilik katsayısı (R²), ortalama yüzde hata (MPE), sapma hatası (MBE), ortalama mutlak hata yüzdesi (MAPE), bağıl hata karesi (SSRE), bağıl standart hata (RSE), ortalama karekök hatası (RMSE), bağıl hata yüzdesi (e) ve t-istatistik (t-sat) ile olmak üzere dokuz farklı istatistik yöntemi ile karşılaştırılmıştır. Şanlıurfa ili için en uygun yaklaşım için bir sonuç verilmiştir. İstatistiksel hata sonuçlarına göre Cheegar ve Chibani Modeli yatay düzleme gelen global güneş ışınımı için Şanlıurfa ilinde kullanılacak en uygun model olarak belirlenmiştir. Sonuç olarak Şanlıurfa ili toplam güneş radyasyonu tahmini için polinom modelin tercih edilmesi önerilmiştir. Bu model verilerine göre Şanlıurfa ili için yıllık güneş enerjisi potansiyeli 4332,020 W/m2 /ay olarak belirlenmiştir
