69 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 10 / 69
Öğe Effects of cutting parameters and point angle on thrust force and delamination in drilling of CFRP(De Gruyter, 2014-11-14) Çelik, Yahya Hışman; Kılıçkap, Erol; Yardımeden, AhmetParts made of composite materials are generally produced by near-net-shape technology. However, additional machining operations such as drilling are often required to facilitate components assembling. Drilling of composite materials is also a common process in the assembly of aerospace and automotive composite structures. During drilling, unlike the conventional materials, a few damage forms may take place. Among these damage forms, the delamination is the most important one. Therefore, the experimental studies carried out on drilling of CFRP composite materials for determining optimum processing parameters are of great importance. In this particular study, delamination in CFRP composites caused by drilling was investigated. The composite material was drilled under various spindle speeds, feed rates and drill point angles. The results showed that delamination and thrust forces were affected by cutting parameters. It was demonstrated that feed rate and drill point angle make the largest contribution to the overall performance.Öğe Numerical and experimental investigation of solar chimney power plant system performance(Taylor & Francis, 2020-03-15) Karakaya, Hakan; Durmuş, Aydın; Avcı, Ali SerkanA prototype of a solar chimney power plant was performed by modeling in this study. The performed prototype was experimentally confirmed. Temperature, velocity, and radiation values were measured to actualize the confirmation. Experimental data that were obtained to determine the performance of solar chimney whose prototype was actualized by the help of measured values were computationally analyzed. The geometry of a solar chimney in the analysis was bidimensionally (2D) drawn on an axis of symmetry. The numerical simulation was analyzed with computational fluid dynamics (CFD) method. Since analysis results show that there is turbulent flow in system (RNG), k-ɛ turbulence model was used. Continuity, momentum, and energy equations were applied to the solar chimney system via the finite volume method. Moreover, DO (discrete ordinates) model was inserted in analysis to evaluate the radiation effect in the collector area. In addition to all these, correlation results between SPSS 17 statistics program and data obtained were evaluated. Finally, with reference to the comparison between numerical and experimental results, data obtained and numerical data are close to each other; the prototype is applicable to the real systems.Öğe Köşeleri yuvarlatılmış eşkenar üçgen delikli kompozit levhaların gerilme ve yüzde uzama davranışlarının deneysel olarak incelenmesi(Nevşehir Hacı Bektaş Veli Üniversitesi, 2016-04) Adin, Hamit; Ergün, Raşit KorayÖğe Investigation of low velocity impact behaviors of honeycomb sandwich composites(SpringerLink, 2018-08-09) Topkaya, Tolga; Solmaz, Murat YavuzHoneycomb sandwich composites are used as significant structural members in advanced engineering applications. Thus, it is critical to determine how they behave under impact loading, in addition to other loads. In this study, low velocity impact loading behaviors of honeycomb sandwich composites were experimentally investigated. Almost all of the design parameters of honeycomb sandwich composites were investigated. The results indicated that the core thickness of honeycomb had no effect on the strength of the composite, and the parameter influencing the impact behavior of the specimen the most was the face sheet thickness. When the face sheet thickness of the specimen was increased, the most apparent strength increase was observed in the models using carbon fiber-reinforced composite face sheets. For all face sheet types subject to impact energy of 10 Joules, the upper face sheets of 0.5 mm-thick specimens were perforatedÖğe Effects of ethanol addition to biodiesel fuels derived from cottonseed oil and its cooking waste as fuel in a generator diesel engine(Taylor & Francis, 2020-03) Karakaya, HakanExploration of energy sources such as renewable and non-edible vegetable oils has been continued during the recent two decades of 2000s. Cottonseed oil is a non-edible, abundant oil and is generally used as cooking oil. In the present study, the usability of biodiesel derived from both cottonseed oil and its cooking wastes was investigated by blending them with ULSD or ethanol in 50 percentages. B50, WB50, B50E50 and WB50E50, biodiesel and ethanol-contained fuels and ULSD were prepared for experiments. Combustion, performance, and emissions tests were conducted on a diesel engine used for power-producing electrical generator. In the combustion tests, cylinder pressure, HRR, CHR, MGT, and MFB were analyzed while MFC, BSFC, exhaust manifold temperature, and thermal efficiency were obtained in the performance tests. In the emissions tests, CO, HC, and NOx emissions were measured and compared with the results of ULSD. Combustion and performance findings of ULSD contained biodiesel blends were found more similar to those of ULSD. The duration of combustion stage can clearly be seen to be narrowed for ethanol-contained blend because of the rabid combustion characteristics of ethanol. Besides, the peak of HRR was found 10% higher for B50E50 while it was found averagely 8% for WB50E50 blends. NOx emissions were found 48% lower averagely for ethanol contained biodiesel blends that it is the most important finding of ethanol using with biodiesel. Besides, HC emissions were also found about 75% for biodiesel contained diesel fuel blends.Öğe Effects of particle reinforcement on the bending and compressive behaviors of composite pipes(Materials Testing, 2019-11) Adin, HamitIn this study, the effects of adding particles to composite pipes were examined. For the study, composite pipes reinforced with particles were produced by using structural epoxy adhesive and mica as the particle. Composite pipes oriented at [-45 °/+45 °] were manufactured by the hand lay-up method. The composite pipes were loaded axially for measuring bending and compressive strength. When bending and compression loads are applied in the experiments it was seen that the particle reinforced methods indicated in the literature have a great effect of on the strength of the bending and compressive behaviour. The results show that addition of particles enhances compressive and bending strength.Öğe Batman ilinin doğal gaz ihtiyacının ve hava kirliliğini azaltmasının matematiksel yöntemlerle modellenmesi(Karabük Üniversitesi, 2009) Aydın, Hüseyin; Yaşar, Fevzi; Bezek Güre, ÖzlemÖğe Milling Inconel 718 workpiece with cryogenically treated and untreated cutting tools(SpringerLink, 2021-07-17) Gürbüz, Hüseyin; Baday, ŞehmusAlthough Inconel 718 is an important material for modern aircraft and aerospace, it is a kind material, which is known to have low machinability. Especially, while these types of materials are machined, high cutting temperatures, BUE on cutting tool, high cutting forces, and work hardening occur. Therefore, in recent years, instead of producing new cutting tools that can withstand these difficult conditions, cryogenic process, which is a heat treatment method to increase the wear resistance and hardness of the cutting tool, has been applied. In this experimental study, feed force, surface roughness, vibration, cutting tool wear, hardness, and abrasive wear values that occurred as a result of milling of Inconel 718 material by means of cryogenically treated and untreated cutting tools were investigated. Three different cutting speeds (35-45-55 m/min) and three different feed rates (0.02- 0.03-0.04 mm/tooth) at constant depth of cut (0.2 mm) were used as cutting parameters in the experiments. As a result of the experiments, lower feed forces, surface roughness, vibration, and cutting tool wear were obtained with cryogenically treated cutting tools. As the feed rate and cutting speed were increased, it was seen that surface roughness, vibration, and feed force values increased. At the end of the experiments, it was established that there was a significant relation between vibration and surface roughness. However, there appeared an inverse proportion between abrasive wear and hardness values. While BUE did not occur during cryogenically treated cutting tools, it was observed that BUE occurred in cutting tools which were not cryogenically treated. Also, in this study, the statistical validity of the experimental values was tested with the help of secondorder equations and analyses of variance (ANOVA). R2 values obtained as 99.14%, 99.76%, and 97.98% for vibration, surface roughness, and feed force values were modeled statistically with the help of second-order equations, respectively.Öğe Damperli kamyonların kasalarında kullanılan pimde oluşan hasarın sonlu elemanlar yöntemiyle analiz(IESS Publishing, 2019-06) Adin, Hamit; Ak, İsmailÖğe Bir derleme olarak hafif alkollerin içten yanmalı motorlarda emisyon karakteristiği(IESS Publishing, 2019) Aydın, Hüseyin; Çelebi, Yahya