10 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 10 / 10
Öğe Milling Inconel 718 workpiece with cryogenically treated and untreated cutting tools(SpringerLink, 2021-07-17) Gürbüz, Hüseyin; Baday, ŞehmusAlthough Inconel 718 is an important material for modern aircraft and aerospace, it is a kind material, which is known to have low machinability. Especially, while these types of materials are machined, high cutting temperatures, BUE on cutting tool, high cutting forces, and work hardening occur. Therefore, in recent years, instead of producing new cutting tools that can withstand these difficult conditions, cryogenic process, which is a heat treatment method to increase the wear resistance and hardness of the cutting tool, has been applied. In this experimental study, feed force, surface roughness, vibration, cutting tool wear, hardness, and abrasive wear values that occurred as a result of milling of Inconel 718 material by means of cryogenically treated and untreated cutting tools were investigated. Three different cutting speeds (35-45-55 m/min) and three different feed rates (0.02- 0.03-0.04 mm/tooth) at constant depth of cut (0.2 mm) were used as cutting parameters in the experiments. As a result of the experiments, lower feed forces, surface roughness, vibration, and cutting tool wear were obtained with cryogenically treated cutting tools. As the feed rate and cutting speed were increased, it was seen that surface roughness, vibration, and feed force values increased. At the end of the experiments, it was established that there was a significant relation between vibration and surface roughness. However, there appeared an inverse proportion between abrasive wear and hardness values. While BUE did not occur during cryogenically treated cutting tools, it was observed that BUE occurred in cutting tools which were not cryogenically treated. Also, in this study, the statistical validity of the experimental values was tested with the help of secondorder equations and analyses of variance (ANOVA). R2 values obtained as 99.14%, 99.76%, and 97.98% for vibration, surface roughness, and feed force values were modeled statistically with the help of second-order equations, respectively.Öğe Analysis of spheroidized AISI 1050 steel in terms of cutting forces and surface quality(Slovenska Akademia Vied, 2016) Baday, Şehmus; Başak, Hüdayim; Güral, AhmetIn this study, the effects of microstructure differences obtained with the application of different spheroidizing heat treatment cycles on medium carbon steel on cutting forces and surface roughness values were investigated. For this purpose, a group of AISI 1050 materials was annealed at 700°C below Ac1 temperature for 720 min and cementite phases were spheroidized by the traditional method. Another group of materials was quenched after austenitization at 850°C for 15 min and then cementites were spheroidized in the ferrite matrix by over-tempering separately at 600°C for 15 and 60 min and at 700°C for 60 min. Machining of the samples was tested under dry cutting conditions in CNC turning center with SNMG 120408 cementite carbide cutting tool and proper PSBNR 2525M12 tool holder with 75-degree edge angle. Cutting forces of traditionally spheroidized samples were lower than the samples spheroidized after quenching. In addition, their cutting forces decreased due to the increase in the average sizes of spheroidal cementite. Minimum surface roughness value was obtained from the samples which were spheroidized at 600°C for 15 min after quenching. However, surface roughness rate of the sample increased as spheroidizing time increased.Öğe Mathematical modelling and optimization of cutting force, tool wear and surface roughness by using artificial neural network and response surface methodology in milling of Ti-6242S(Applied Sciences-Basel, 2017-10-15) Çelik, Yahya Hışman; Kılıçkap, Erol; Yardımeden, AhmetIn this paper, an experimental study was conducted to determine the effect of different cutting parameters such as cutting speed, feed rate, and depth of cut on cutting force, surface roughness, and tool wear in the milling of Ti-6242S alloy using the cemented carbide (WC) end mills with a 10 mm diameter. Data obtained from experiments were defined both Artificial Neural Network (ANN) and Response Surface Methodology (RSM). ANN trained network using Levenberg-Marquardt (LM) and weights were trained. On the other hand, the mathematical models in RSM were created applying Box Behnken design. Values obtained from the ANN and the RSM was found to be very close to the data obtained from experimental studies. The lowest cutting force and surface roughness were obtained at high cutting speeds and low feed rate and depth of cut. The minimum tool wear was obtained at low cutting speed, feed rate, and depth of cut.Öğe Investigation of experimental study of end milling of CFRP composite(De Gruyter, 2013-12-12) Çelik, Yahya Hışman; Kılıçkap, Erol; Yardımeden, AhmetCarbon fiber-reinforced plastic (CFRP) composites are materials that are difficult to machine due to the anisotropic and heterogeneous properties of the material and poor surface quality, which can be seen during the machining process. The machining of these materials causes delamination and surface roughness owing to excessive cutting forces. This causes the material not to be used. The reduction of damage and surface roughness is an important aspect for product quality. Therefore, the experimental study carried out on milling of CFRP composite material is of great importance. End milling tests were performed at CNC milling vertical machining center. In the experiments, parameters considered for the end milling of CFRP were cutting speed, feed rate, and flute number of end mill. The results showed that damage, surface roughness, and cutting forces were affected by cutting parameters and flute number of end mill. The best machining conditions were achieved at low feed rate and four-flute end mill.Öğe Effect of MQL flow rate on machinability of AISI 4140 steel(Taylor & Francis, 2020-06-27) Gürbüz, Hüseyin; Gönülaçar, Yunus Emre; Baday, ŞehmusMany studies were performed about the influence of minimum quantity lubrication (MQL) technique on cutting performance in the literature, but there is no paper examining the effect of different MQL flow rates and cutting parameters on machinability of AISI 4140 material as a whole. In this study, the effects of different MQL flow rates and cutting parameters on surface roughness, main cutting force and cutting tool flank wear (VB), with great importance among the machinability criteria, and forming as a result of the machining of AISI 4140, were revealed. At the end of the experiments, it was determined that rise of flow rate affected main cutting forces positively to a certain extent; yet, it exhibited no significant effect on surface roughness, but reduced VB. Also, it was observed that both main cutting force and surface roughness increased with the increase of feed, while generally decreased with the increase of cutting speed. It was seen that flank wear was positively affected by the increase in flow rate; and this decreased with the increase in flow rate. R2 values obtained as 99.8% and 99.9% for main cutting forces and surface roughness values modeled statistically with the help of quadratic equations, respectively.Öğe Estimate of cutting forces and surface roughness in end milling of glass fiber reinforced plastic composites using fuzzy logic system(Walter de Gruyter, 2014-06-01) Çelik, Yahya Hışman; Kılıçkap, Erol; Yardımeden, AhmetMilling glass fiber reinforced plastic (GFRP) composite materials are problematic, owing to, e.g., nonhomogeneous and anisotropic properties and effects of plastic deformation. To reduce these problems, the effects of cutting speed, feed rate, and the number of flutes on surface roughness and of thrust forces occurring during the milling of GFRP composite materials were investigated by both experimental and fuzzy logic models. Experiments were performed at 30 m/min, 60 m/min, and 90 m/min cutting speeds, at 0.1 mm/rev, 0.15 mm/rev, and 0.2 mm/rev feed rates and 10 mm diameters in a cemented carbide end mill, which has two, three, and four flutes without cutting fluids. The values obtained from experiments were defined by a fuzzy logic model. A fuzzy logic model was employed to estimate the surface roughness and thrust forces for different cutting parameters. As a result of both the experimental study and the fuzzy logic model, while the minimum thrust force was obtained at low cutting speeds, and feed rates and a high number of flutes end mill, the best surface quality was obtained at low feed rates, high cutting speed, and number of flutes end mill.Öğe Estimation of surface roughness and cutting speed in CNC WEDM by artificial neural network that employed trainable activation function(SAGE Journals, 2021-02-01) Gürbüz, HüseyinActivation functions are the most significant properties of artificial neural networks (ANN) because these functions are directly related with the ability of ANN in learning or modelling a system or a function. Furthermore, another reason for the significance of the fact that determination of optimal activation function in ANN is its relationship with success level. In this experimental study, the effects of different types of wire electrodes, cooling techniques and workpiece materials on surface roughness (Ra) and cutting speed (Vc) in wire electrical discharge machining (WEDM) were investigated by using trainable activation functions (AFt) and modelling them in ANNs. So far, a number of methods have been performed according to the data set in order to optimally predict Ra and Vc results. Among these methods, randomized ANN with AFt was found to be the best one for robust prediction according to RMSE values. While the value was 0.280 for Vc, it was 0.2104 for Ra. Optimum activation functions in Ra and Vc were found at first and third degree trainable functions, respectively.Öğe An experimental investigation of the effects of point angle on the high-speed steel drills performance in drilling(SAGE, 2018-11) Demir, ZülküfThe differences in the cutting speed are a serious problem along the cutting edge of the drill, in drilling operations. This problem can partly be solved reducing the length of the cutting edge via changing the drill point angle. In addition, in this study, the effect of point angle, feed rate, and cutting speed on drilling is investigated. For identifying the optimum cutting parameters, AISI 1050 steel alloy was selected as the experimental specimen, these specimen were pre-drilled 5 mm in diameter due to eliminating the effect of the chisel edge. In the experiments, the holes were drilled only at a depth of 10 mm in order not to give any harm to the dynamometer while measuring thrust force. For this aim, in drilling process, drills with point angle of 100°, 118°, 136°, 154°, and 172° were selected. In conclusion, the thrust force, the tool wear, and the surface roughness linearly decreased with increasing point angles due to less removal chip area, in per revolve of the tool. However, the thrust force, the tool wear, and the surface roughness were adversely affected at higher feed rates and lower cutting speeds. The hole dimensional accuracy decreased at lower feed rates and cutting speeds but at higher point angles and concurrently at higher feed rates but lower point angles and cutting speeds. However, the hole dimensional accuracy showed more decisiveness at 118° than other point angles, while the highest dimensional accuracy values recorded at 136° point angle, at higher cutting speeds.Öğe Investigating the effects of cutting parameters on the hole quality in drilling the Ti-6Al-4V alloy(Materiali in Tehnologije, 2014-10) Çelik, Yahya HışmanIn this study, the effects of cutting parameters on the surface roughness, burr height, hole-diameter deviation, cutting temperature and structure of a chip formation were investigated during the drilling of the Ti-6Al-4V alloy. For this purpose, the Ti-6Al-4V alloy was drilled at different cutting parameters, longitudinally in the 10 mm depth with Ø = 10 mm high-speed-steel (HSS) drills, having 90°, 118°, 130° and 140° point angles on the CNC vertical machining centre. Experiments were carried out at the (12.5, 18.75 and 25) m/min cutting speeds and the (0.05, 0.1 and 0.15) mm/r feed rates without using the cutting fluid. As a result, as the feed rate and the drill-point angle were increased, the surface roughness increased as well; however, as the cutting speed increased, the surface roughness decreased. When the feed rate and drill-point angle increased, the burr height decreased. On the other hand, an increase in the cutting speed increased the burr height. In general, an increase in the feed rate and drill-point angle increased the hole diameters, and the hole diameters obtained were close to the nominal size when the cutting speed was increased.Öğe An investigation of the effect of parameters and chip slenderness ratio on drilling process quality of AISI 1050 steel(Hindawi, 2018-05-08) Demir, Zülküf; Yakut, RıfatThe chip slenderness ratio is a vital parameter in theoretical and applicable machining operations. In predrilled drilling operations of AISI 1050 steel alloy, HSS drills were employed, and the effect of the selected parameters on the chip slenderness ratio and also the effect of the chip slenderness ratio on the thrust force, surface roughness, drilled hole delamination, tool wear, and chip morphology were investigated. The major parameters, influential on the chip slenderness ratio, were feed rate and point angle, while spindle speed was too small to be negligible. With increasing the chip slenderness ratio, the thrust force and the tool wear decreased, which resulted in appropriate chip morphology, but there were increases in surface roughness. However, the chip slenderness ratio had no effect on the drilled hole delamination.
