4 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 4 / 4
Öğe Hardness and wear behaviours of al matrix composites and hybrid composites reinforced with B 4 C and SiC(Springer Nature, 2019-01-15) Çelik, Yahya Hışman; Kılıçkap, ErolThe conversion into the desired shape of the metal powders using Powder Metallurgy (PM) method enables economically mass productions. This case allows producing parts with complex and high dimensional accuracy with no machining. In this study the composites and hybrid composites with Al matrix were produced using PM method with different ratios B4C and SiC. Microhardness and wear experiments of the produced composites were investigated. Wear experiments were performed at a constant speed of 0.5 m/s, application loads of 5, 10 and 15 N and sliding distances of 250, 500, and 750 m. Then, SEM images of composites and hybrid composites were captured. The increase of the reinforcement ratio in the composites contributed to the increase of the hardness. The highest hardness value was computed as 58.7 HV from 16% B4C reinforced composite. In addition, the increase in the reinforcement ratio contributed to the increase of the wear resistance. The increase in the load and sliding distance also increased the wear. The minimum weight loss was calculated as 18 mg from 5 N load, 250 m sliding distance and 16% SiC reinforced composite.Öğe Investigation of wear behaviours of Al matrix composites reinforced with different B4C rate produced by powder metallurgy method(Elsevier, 2017-09) Çelik, Yahya Hışman; Seçilmiş, KübraIn this study, the effects of wear behaviours of Al matrix composites reinforced with different B4C rate produced by powder metallurgy method were investigated. Al and B4C powders with purity of 99.9% and sizes of 25–44 µm were prepared as pure Al, 4% B4C/Al, 8% B4C/Al, 12% B4C/Al and 16% B4C/Al. After these prepared mixtures were pressed under 350 MPa, they were sintered for 90 min at 580 °C in atmospheric environment. Microhardness and wear tests of the produced samples were carried out. Wear experiments of these composites were performed with specially manufactured test equipment at different application loads (5 N, 10 N and 15 N), different sliding distances (250 m, 500 m, 750 m and 1000 m) and a constant speed of 0.46 m/s. In addition, optical microscope, SEM, EDS analyses were used to determine the microstructural changes in the worn and unworn surface of the manufactured composite materials. The results of experimental studies show that the increasing the B4C reinforced rate in composites with Al matrix has led to increase of the hardness and to reduce of the wear loss.Öğe Effects of natural hard shell particles on physical, chemical, mechanical and thermal properties of composites(SAGE Journals, 2021-05-31) Çelik, Yahya Hışman; Çelik, Kadir Serdar; Kılıçkap, ErolShelled herbal foods are widely consumed. The evaluation of the shells of these foods is important due to their features such as low cost, ease of recycling and environmental friendliness. In this study, hazelnut shell (HS), pistachio shell (PS), and apricot kernel shell (AKS) were brought to powder particles by grinding to dimensions of 300–425 µm. Some of the powder particles were converted into ash at 900°C. The amounts of cellulose, ash, humidity, and metal in these particles via chemical analyses were determined, while their structural properties via X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) analyses. Composite materials were produced by adding 15 wt.% to the polyester matrix material from these powder particles and ashes. Compression strength, hardness, specific weight, and thermal conductivity of these composites were analyzed. The lowest and highest humidity, ash, cellulose, hemicellulose, and lignin ratios in powders showed differences depending on the type of powders. The amount of Sn and K in the HS, PS, and AKS powders were close to each other, while the amount of Ca, Na, Mg, Fe, Mn, Cu, Zn and Si was higher in AKS powder. The reinforcement adding to the polyester increased the compression strength, hardness, specific weight and thermal conductivity properties.Öğe Investigating the effects of cutting parameters on materials cut in CNC plasma(Taylor & Francis, 2013-10-03) Çelik, Yahya HışmanComplex-profile surfaces, of which measurement precision is not important, are cut serially using CNC plasma. These materials cut using CNC plasma are assembled with different manufacturing techniques. These materials can also operate under high pressure and resistance. In this study, S235JR sheet materials (4, 6, and 8 mm thick), used in pressure vessels, were cut using the CNC plasma cutting machine at different cutting speeds, amperes, and arc voltages. Temperature distribution, thickness of heat-affected zone (HAZ), surface roughness, and hardness were measured from the material cut at these different values. Based on values obtained from measurements, the ideal cutting conditions were identified for the materials exposed to the cutting procedures.
