Arama Sonuçları
Listeleniyor 1 - 10 / 517
Öğe Otomotiv fren balatalarının sürtünme performansında sic etkisi(Uludağ Üniversitesi, 2012-06) Altun, Şehmus; Öner, Cengiz; Sugözü, İlkerBu çalışmada, yüksek mukavemet, düşük aşınma, daha fazla yük ve sıcaklık dayanımı özelliklerine sahip SiC içeren balata numunelerinin sürtünme katsayısı ve aşınma dayanımına etkisi incelenmiştir. Balata bileşeni içerisine %5, %10 ve %15 SiC ilave edilmiştir. Sonuç olarak, SiC oranı arttıkça aşınma direnci artmış ve sürtünme katsayısı azalmıştırÖğe Uluslararası kültürel miras mevzuatı(Kültürel Mirasın Dostları Derneği, 2007) Aydın, Mahmut; Öz, Ali Kazım; Güner, Saadet; Aydın, Mahmut; Öz, Ali Kazım; Güner, Saadet; Kapan, DenizÖğe N-type InP Schottky diodes with organic thin layer: Electrical and interfacial properties(Journal of Vacuum Science & Technology B, 2010-03) Güllü, Ömer; Turut, AbdulmecitThe rectifying junction characteristics of methyl red (MR) organic film on n-type InP substrate have been studied. It has been observed that MR-based structure shows an excellent rectifying behavior and that the MR film increases the effective barrier height by influencing the space charge region of the n-type InP. The barrier height and ideality factor values for this structure have been obtained as 0.75 eV and 1.93 from the forward bias current-voltage characteristics, respectively. By using capacitance-voltage characteristics at 1 MHz, the barrier height and the carrier concentration values have been calculated as 0.93 eV and 5.13×1015 cm−3, respectively. The energy distributions of the interface states and their relaxation times have been determined from the forward bias capacitance-frequency and conductance-frequency characteristics. Moreover, it was seen that both the interface-state density and the relaxation time of the interface states decreased with bias voltage from experimental results.Öğe Investigation of plasma arc cutting parameters with type-2 fuzzy set and system(De Gruyter, 2013-10) Çelik, Yahya Hışman; Özek, Cebeli; Bulut Özek, MüzeyyenThe objective of the present study was it to design a type-2 fuzzy set and system in order to predict surface roughness and hardness depending on the parameters (material thickness, cutting speed, arc voltage and current) of the plasma arc cutting process of S235JR sheet materials. Therefore, some experimental studies were conducted. The experimentally determined data were used to describe the type-2 fuzzy set and system. Type-2 fuzzy set and system was found to be usefull to predict surface roughnes and hardness. According to the obtained values, the best surface roughness and the values closest to the hardness of the raw material were obtained at 1500 mm/min cutting speed, 8 mm material thickness, 115 V arc voltage and 80 A current.Öğe Effects of cutting parameters and point angle on thrust force and delamination in drilling of CFRP(De Gruyter, 2014-11-14) Çelik, Yahya Hışman; Kılıçkap, Erol; Yardımeden, AhmetParts made of composite materials are generally produced by near-net-shape technology. However, additional machining operations such as drilling are often required to facilitate components assembling. Drilling of composite materials is also a common process in the assembly of aerospace and automotive composite structures. During drilling, unlike the conventional materials, a few damage forms may take place. Among these damage forms, the delamination is the most important one. Therefore, the experimental studies carried out on drilling of CFRP composite materials for determining optimum processing parameters are of great importance. In this particular study, delamination in CFRP composites caused by drilling was investigated. The composite material was drilled under various spindle speeds, feed rates and drill point angles. The results showed that delamination and thrust forces were affected by cutting parameters. It was demonstrated that feed rate and drill point angle make the largest contribution to the overall performance.Öğe Tarihi eserlerin korozyonu ve korunması(Mustafa Kemal Üniversitesi, 2018) Aydın, MahmutÖğe Doğal fiber takviyeli kompozitler üzerine bir derleme çalışması(IESS Publishing, 2019-06) Çelik, Yahya Hışman; Yalçın, RojinÖğe General conditions, problems and expectations of Syrian migrants in Turkey(Akademisyen Kitabevi, 2019-06-17) Türk, Emrullah; Nerse, SerdarThe directors of Academician Publishing House, have been conducting their commercial activities for a long time by transferring their 30 years of broadcasting experience to their legal entities. In the said period, it was proud to publish 750 books, particularly health and social sciences, cultural and artistic topics. The Academician, that defines the platform of being an international publishing house, is in the pursuit of creating a global brand in addition to broadcasting in Turkish and foreign languages. The books, which are considered as permanent documents of scientific and intellectual studies, are the witnesses of hundreds of years as an information recording platform. The future of the book, which has built on a solid basis with the invention of the printing press, will certainly have a place in our lives for a long period of time, even though it has moved into orbit of new inventions. Academician Publishing House has started the process of publishing books in international quality and quantity with its own name of “Scientific Research Book” series in Turkish and English. The publication process, which will take place in March and September every year, will continue with thematic sub titles. We owe to our thanks to all of our researchers who supported this process, which was starting with about 30 books, and to everyone in the backgroundÖğe XVII. Yüzyılın ikinci yarısında İstanbul’da halkın temel ihtiyaç maddelerinden ekmeğin temini(Acta Turcica Tematik Türkoloji, 2015-03) Türkmen, Mustafa NuriÖğe Görüntülerin esinleyici gücünün geleceğe yönelik yeni düşünceler oluşturmasındaki rolü(Ankara Üniversitesi, 2012-11) Uzun Aydın, Derya; Cereci, Sedat
