129 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 10 / 129
Öğe N-type InP Schottky diodes with organic thin layer: Electrical and interfacial properties(Journal of Vacuum Science & Technology B, 2010-03) Güllü, Ömer; Turut, AbdulmecitThe rectifying junction characteristics of methyl red (MR) organic film on n-type InP substrate have been studied. It has been observed that MR-based structure shows an excellent rectifying behavior and that the MR film increases the effective barrier height by influencing the space charge region of the n-type InP. The barrier height and ideality factor values for this structure have been obtained as 0.75 eV and 1.93 from the forward bias current-voltage characteristics, respectively. By using capacitance-voltage characteristics at 1 MHz, the barrier height and the carrier concentration values have been calculated as 0.93 eV and 5.13×1015 cm−3, respectively. The energy distributions of the interface states and their relaxation times have been determined from the forward bias capacitance-frequency and conductance-frequency characteristics. Moreover, it was seen that both the interface-state density and the relaxation time of the interface states decreased with bias voltage from experimental results.Öğe Effects of cutting parameters and point angle on thrust force and delamination in drilling of CFRP(De Gruyter, 2014-11-14) Çelik, Yahya Hışman; Kılıçkap, Erol; Yardımeden, AhmetParts made of composite materials are generally produced by near-net-shape technology. However, additional machining operations such as drilling are often required to facilitate components assembling. Drilling of composite materials is also a common process in the assembly of aerospace and automotive composite structures. During drilling, unlike the conventional materials, a few damage forms may take place. Among these damage forms, the delamination is the most important one. Therefore, the experimental studies carried out on drilling of CFRP composite materials for determining optimum processing parameters are of great importance. In this particular study, delamination in CFRP composites caused by drilling was investigated. The composite material was drilled under various spindle speeds, feed rates and drill point angles. The results showed that delamination and thrust forces were affected by cutting parameters. It was demonstrated that feed rate and drill point angle make the largest contribution to the overall performance.Öğe XVII. Yüzyılın ikinci yarısında İstanbul’da halkın temel ihtiyaç maddelerinden ekmeğin temini(Acta Turcica Tematik Türkoloji, 2015-03) Türkmen, Mustafa NuriÖğe Küllüoba’da İlk Tunç Çağı'nda beslenme alışkanlıkları ve bölgesel karşılaştırması(Arkeoloji ve Sanat, 2019) Gündem, Can YumniÖğe Köşeleri yuvarlatılmış eşkenar üçgen delikli kompozit levhaların gerilme ve yüzde uzama davranışlarının deneysel olarak incelenmesi(Nevşehir Hacı Bektaş Veli Üniversitesi, 2016-04) Adin, Hamit; Ergün, Raşit KorayÖğe Investigation of low velocity impact behaviors of honeycomb sandwich composites(SpringerLink, 2018-08-09) Topkaya, Tolga; Solmaz, Murat YavuzHoneycomb sandwich composites are used as significant structural members in advanced engineering applications. Thus, it is critical to determine how they behave under impact loading, in addition to other loads. In this study, low velocity impact loading behaviors of honeycomb sandwich composites were experimentally investigated. Almost all of the design parameters of honeycomb sandwich composites were investigated. The results indicated that the core thickness of honeycomb had no effect on the strength of the composite, and the parameter influencing the impact behavior of the specimen the most was the face sheet thickness. When the face sheet thickness of the specimen was increased, the most apparent strength increase was observed in the models using carbon fiber-reinforced composite face sheets. For all face sheet types subject to impact energy of 10 Joules, the upper face sheets of 0.5 mm-thick specimens were perforatedÖğe Kadınlar Dünyası Gazetesinin Milli Hâkimiyet konusuna yaklaşımı(Van Yüzüncü Yıl Üniversitesi, 2019-12) Özteke, FahriÖğe Troas bölgesinin MÖ 3. bin yıl hayvancılık ekonomisini anlamak(İçdaş Yayınları, 2018-10) Gündem, Can YumniÖğe Effects of particle reinforcement on the bending and compressive behaviors of composite pipes(Materials Testing, 2019-11) Adin, HamitIn this study, the effects of adding particles to composite pipes were examined. For the study, composite pipes reinforced with particles were produced by using structural epoxy adhesive and mica as the particle. Composite pipes oriented at [-45 °/+45 °] were manufactured by the hand lay-up method. The composite pipes were loaded axially for measuring bending and compressive strength. When bending and compression loads are applied in the experiments it was seen that the particle reinforced methods indicated in the literature have a great effect of on the strength of the bending and compressive behaviour. The results show that addition of particles enhances compressive and bending strength.Öğe Batman ilinin doğal gaz ihtiyacının ve hava kirliliğini azaltmasının matematiksel yöntemlerle modellenmesi(Karabük Üniversitesi, 2009) Aydın, Hüseyin; Yaşar, Fevzi; Bezek Güre, Özlem
