Arama Sonuçları
Listeleniyor 1 - 10 / 62
Öğe Biodiesel production from inedible animal tallow and an experimental investigation of its use as alternative fuel in a direct injection diesel engine(Elsevier, 2009-02-15) Altun, Şehmus; Öner, CengizIn this study, a substitute fuel for diesel engines was produced from inedible animal tallow and its usability was investigated as pure biodiesel and its blends with petroleum diesel fuel in a diesel engine. Tallow methyl ester as biodiesel fuel was prepared by base-catalyzed transesterification of the fat with methanol in the presence of NaOH as catalyst. Fuel properties of methyl ester, diesel fuel and blends of them (5%, 20% and 50% by volume) were determined. Viscosity and density of fatty acid methyl ester have been found to meet ASTM D6751 and EN 14214 specifications. Viscosity and density of tallow methyl esters are found to be very close to that of diesel. The calorific value of biodiesel is found to be slightly lower than that of diesel. An experimental study was carried out in order to investigate of its usability as alternative fuel of tallow methyl ester in a direct injection diesel engine. It was observed that the addition of biodiesel to the diesel fuel decreases the effective efficiency of engine and increases the specific fuel consumption. This is due to the lower heating value of biodiesel compared to diesel fuel. However, the effective engine power was comparable by biodiesel compared with diesel fuel. Emissions of carbon monoxide (CO), oxides of nitrogen (NOx), sulphur dioxide (SO2) and smoke opacity were reduced around 15%, 38.5%, 72.7% and 56.8%, respectively, in case of tallow methyl esters (B100) compared to diesel fuel. Besides, the lowest CO, NOx emissions and the highest exhaust temperature were obtained for B20 among all other fuels. The reductions in exhaust emissions made tallow methyl esters and its blends, especially B20 a suitable alternative fuel for diesel and thus could help in controlling air pollution. Based on this study, animal tallow methyl esters and its blends with petroleum diesel fuel can be used a substitute for diesel in direct injection diesel engines without any engine modification.Öğe Combustion, performance and emissions of a diesel power generator fueled with biodiesel-kerosene and biodiesel-kerosene-diesel blends(Elsevier, 2017-02-05) Bayındır, Hasan; Işık, Mehmet Zerrakki; Argunhan, Zeki; Yücel, Halit Lütfi; Aydın, HüseyinHigh percentages of biodiesel blends or neat biodiesel cannot be used in diesel engines due to high density and viscosity, and poor atomization properties that lead to some engine operational problems. Biodiesel was produced from canola oil by transesterification process. Test fuels were prepared by blending 80% of the biodiesel with 20% of kerosene (B80&K20) and 80% of the biodiesel with 10% of kerosene and 10% diesel fuel (B80&K10&D10). Fuels were used in a 4 cylinders diesel engine that was loaded with a generator. Combustion, performance and emission characteristics of the blend fuels and D2 in the diesel engine for certain loads of 3.6, 7.2 and 10.8 kW output power and 1500 rpm constant engine speed were experimented and deeply analyzed. It was found that kerosene contained blends had quite similar combustion characteristics with those of D2. Mass fuel consumption and Bscf were slightly increased for blend fuels. HC emissions slightly increased while NOx emissions considerably reduced for blends. It was resulted that high percentages of biodiesel can be a potential substitute for diesel fuel provided that it is used as blending fuel with certain amounts of kerosene.Öğe Effects of ethanol addition to biodiesel fuels derived from cottonseed oil and its cooking waste as fuel in a generator diesel engine(Taylor & Francis, 2020-03) Karakaya, HakanExploration of energy sources such as renewable and non-edible vegetable oils has been continued during the recent two decades of 2000s. Cottonseed oil is a non-edible, abundant oil and is generally used as cooking oil. In the present study, the usability of biodiesel derived from both cottonseed oil and its cooking wastes was investigated by blending them with ULSD or ethanol in 50 percentages. B50, WB50, B50E50 and WB50E50, biodiesel and ethanol-contained fuels and ULSD were prepared for experiments. Combustion, performance, and emissions tests were conducted on a diesel engine used for power-producing electrical generator. In the combustion tests, cylinder pressure, HRR, CHR, MGT, and MFB were analyzed while MFC, BSFC, exhaust manifold temperature, and thermal efficiency were obtained in the performance tests. In the emissions tests, CO, HC, and NOx emissions were measured and compared with the results of ULSD. Combustion and performance findings of ULSD contained biodiesel blends were found more similar to those of ULSD. The duration of combustion stage can clearly be seen to be narrowed for ethanol-contained blend because of the rabid combustion characteristics of ethanol. Besides, the peak of HRR was found 10% higher for B50E50 while it was found averagely 8% for WB50E50 blends. NOx emissions were found 48% lower averagely for ethanol contained biodiesel blends that it is the most important finding of ethanol using with biodiesel. Besides, HC emissions were also found about 75% for biodiesel contained diesel fuel blends.Öğe Investigation of the usability of biodiesel obtained from residual frying oil in a diesel engine with thermal barrier coating(Journals & Books, 2015-04-05) Aydın, Hüseyin; Sayın, Cenk; Aydın, SelmanIn this study, biofuel was produced from residual frying oil of cottonseed and D2, B5 and B100 fuels were prepared in order to use in experiments. These fuels were tested in a single cylinder, four strokes, 3 LD 510 model Lombardini CI engine. Then the top surfaces of the piston and valves were coated with plasma spray coating method by using 100 μm of NiCrAl as lining layer and over this layer the same surfaces were coated with 400 μm of the mixture that consists of %88 ZrO2, %4 MgO and %8 Al2O3. After the coating process, above mentioned fuels were tested in the coated engine. Previously, same fuels had been tested in uncoated engine, at full load and various speeds. Performance, emission and combustion experiments were carried out in coated engine. By coating process, partial increases were observed in power, exhaust manifold temperature and engine noise, while partial decreases were seen in brake specific fuel consumption (Bsfc). Besides, partial reductions were found in carbon monoxide (CO), hydrocarbon (HC) and smoke opacity emissions, but partial increases were observed in nitrogen oxide (NOx) emissions. Cylinder gas pressure values were higher for coated engine. Moreover, heat releases were close to each other in both engines.Öğe Aspir ve kanola biyodizeli kullanımının egzoz emisyonu ve motor performansına etkilerinin incelenmesi(Küresel Mühendislik Çalışmaları Dergisi, 2016-04-01) Aydın, Hüseyin; Işık, Mehmet Zerrakki; Ziyadanoğulları Budak, Neşe; Oktay, Hasan; Bayındır, Hasan; Yücel, Halit LutfiBiodiesel fuel, which can be produced from crude or waste vegetable oil, is an important alternative renewable fuel for diesel engines. Particularly the use of vegetable oils for diesel engines has found an important place in several surveys. Biodiesel can be used alone, or blended with petrodiesel in any proportions. Biodiesel is suitable for usage at conventional diesel engines without modification. In this study, canola and safflower oil biodiesel methyl is realized by using the esterification method.. The produced biodiesels were blended in %(50) (in volume) with diesel fuel. The blends were tested in a four cycle, four cylinder Diesel engine. The effects of biodiesel addition to Diesel No. 2 on the performance and emissions of the engine were examined at full load. The resulting performance values were found to be similar to diesel fuel. In general, specific fuel consumption of biodiesel is higher than diesel at all engine loads. Significant difference between the exhaust temperature is not determined. AB50 biodiesel compared to diesel HC emissions at high loads began to decline. NOx, CO2 and O2 emissions ratio has increased at high loads for Biodiesel fuels. Experimental results showed that the produced biodiesels can be partially substituted for the diesel fuel at most operating conditions in terms of the performance parameters and emissions without any engine modification and preheating of the blends.Öğe An analysis of biodiesel requirement, production and policies in Turkey(e-Journal of New World Sciences Academy, 2008-02-01) Aydın, Hüseyin; Bayındır, HasanThe development of alternative fuels from renewable resources, like biomass, has gained considerable attention in recent years. A biodiesel program would give many benefits in terms of generation of employment for poor/rural people, farmers, accelerate of starting many type of industries for developing countries like Turkey. This paper investigates current status of biodiesel in Turkey, advantages and disadvantages of biodiesel in diesel engines, annual diesel fuel consumption, import and export ratings and annual diesel fuel demand. The main focus of this paper is on Turkey’s current fuel status and to clarify Turkey’s biodiesel demand as alternative to fossil diesel fuel. Results show that Turkey is highly in need of alternative energies such as bio-fuels. That’s way it is recommended that Turkey should promote oilseed crops farming to the rise production of biodiesel.Öğe Hayvansal iç yağlardan transesterifikasyon reaksiyonu ile biyodizel üretilmesi(Doğu Anadolu Bölgesi Araştırma ve Uygulama Merkezi, 2008-07-31) Altun, Şehmus; Öner, CengizHayvansal yağlar normal çevre sıcaklığında katı ve çok viskozdurlar. Yüksek viskozitelerinden dolayı dizel motorlarında kullanılmadan önce modifiye edilmeleri gerekmektedir. Hayvansal yağların dizel motorlarında kullanılabilirliliğini iyileştirmek için emülsiyon ve transesterifikasyon etkili iki yöntemdir. Bu çalışmada hayvansal iç yağlardan baz katalizörlü transesterifikasyon ile %99.7 saflıkta metil alkol ve katalizör olarak %98 saflıkta NaOH kullanılarak hayvansal iç yağı metil esteri (biyodizel) üretilmiştir. Hayvansal iç yağı, metil ester şekline dönüştükten sonra viskozitesi önemli ölçüde azalmış ve oda sıcaklığında sıvı fazında bir yakıt elde edilmiştir. Biyodizelin belirlenen yakıt özellikleri ASTM standartlarında olup, viskozitesi ve yoğunluğu dizel yakıtına yakın, ısıl değeri ise %8 daha düşük çıkmıştır.Öğe Atık kızartma yağı metil esterinin bir dizel motorunda motor performansı ve egzoz emisyonlarına etkisinin araştırılması(Fırat Üniversitesi, 2011-05) Aydın, Hüseyin; Behçet, Rasim; Aydın, Selman; İlkılıç, Cumali; Çakmak, AbdülvahapPetrolün sınırlı rezervleri vardır ve gün geçtikçe azalır. Çevre kirliliği ve zararlı yakıtların yanması sonucu ortaya çıkan emisyonlardır. petrol ürünü. Bu alternatif arayışını sürdürür Yukarıda bahsedilen iki temel sorunu çözmek için yakıtlar. Bunda alternatif bir yakıt kaynağı olduğu düşünüldüğünde, atık Yemeklik yağ üretilen biyodizel yakıtı dizel yakıtla karıştırıldı hacimce %25 (B25), %50 (B50) ve %80 (B80) oranlarında ve dizel motorda test edilmiştir. Karışımdan elde edilen test sonuçları yakıtlar, elde edilenlerle karşılaştırılarak sunuldu. dizel yakıt.Öğe Performance and emission analysis of cottonseed oil methyl ester in a diesel engine(Elsevier, 2010-03) Aydın, Hüseyin; Bayındır, HasanIn this study, performance and emissions of cottonseed oil methyl ester in a diesel engine was experimentally investigated. For the study, cottonseed oil methyl ester (CSOME) was added to diesel fuel, numbered D2, by volume of 5%(B5), 20%(B20), 50%(B50) and 75%(B75) as well as pure CSOME (B100). Fuels were tested in a single cylinder, direct injection, air cooled diesel engine. The effects of CSOME-diesel blends on engine performance and exhaust emissions were examined at various engine speeds and full loaded engine. The effect of B5, B20, B50, B75, B100 and D2 on the engine power, engine torque, bsfc's and exhaust gasses temperature were clarified by the performance tests. The influences of blends on CO, NOx, SO2 and smoke opacity were investigated by emission tests. The experimental results showed that the use of the lower blends (B5) slightly increases the engine torque at medium and higher speeds in compression ignition engines. However, there were no significant differences in performance values of B5, B20 and diesel fuel. Also with the increase of the biodiesel in blends, the exhaust emissions were reduced. The experimental results showed that the lower contents of CSOME in the blends can partially be substituted for the diesel fuel without any modifications in diesel engines.Öğe Farklı tozlarla yanma odası yüzeyleri termal yalıtılmış bir dizel motorunda biyoyakıt kullanımının yalıtım malzemesi ve motor parçaları üzerindeki etkileri(Batman Üniversitesi, 2016) Aydın, Selman; Sayın, Cenk; Kılıç, MusaBu çalışmada, plazma püskürtme yöntemiyle farklı tozlarla yanma odası yüzeyi yalıtılmış bir dizel motorunda, uzun bir çalışmadan sonra kaplama tabakasının mikroyapı analizi ve çalışma performansına etkileri incelenmiştir. İlk önce motorun yanma odasına bakan piston ve supaplarının alın yüzeyleri, motorun sıkıştırma oranı değişmeyecek şekilde, plazma sprey yöntemi ile 100 μm kadar NiCrAl astar tabaka ve bu tabakanın üzerine 400 μm olmak üzere %88 ZrO2, %4 MgO ve %8 Al2O3 ana kaplama malzemesi ile kaplanmıştır. Daha sonra yalıtılmış bu dizel motorda 1800 d/d’da ve biyoyakıt ile uzun süre çalıştırılarak biyoyakıtın motor parçaları ve termal bariyerle kaplanmış malzeme üzerindeki etkileri incelenmiştir. Çalışma sonucunda, yanma odası parçalarının plazma püskürtme yöntemi ile kaplanabilirliği, piston ve supapların verimliliğini arttırabildiği tespit edilmiştir. Ayrıca, makroyapı ve SEM (Taramalı Elektron Mikroskobu) incelemeleri sonucunda tabakalar arası bağlanmanın iyi bir şekilde gerçekleştiği, kaplama tabakasında hiçbir gözenek ve çatlak gibi süreksizlerin oluşmadığı görülmüştür.
