4 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 4 / 4
Öğe Strength and failure analysis of inverse Z joints bonded with Vinylester Atlac 580 and Flexo Tix adhesives(Springer, 2012-11) Adin, Hamit; Turgut, AydınIn this study, the tensile strength and failure loads of the inverse Z joints were analyzed both experimentally and numerically by using two adhesives with different properties under a tensile load. Vinylester Atlac 580 and Flexo Tix were used as adhesives and the joints were prepared with two different composite materials. Initially, the mechanical properties of the adhesives were specified using bulk specimens. Then, the stress analyses were performed using three-dimensional finite element method (3-D FEM) via Ansys (V.10.0.1). The experimental results were compared with the numerical results and they were found quite reasonable. According to the test results, it can be seen that when the adherend thickness is increased, the stress increases as well. The most appropriate value of the adherend thickness is identified as t = 5 mm. Furthermore, it was observed that the lowest failure load was obtained at t = 3 mm the thickness for each specimen.Öğe The effects of width on the strength of adhesively bonded Z joints subjected to tensile loads(Taylor & Francis, 2012-11-15) Adin, HamitIn this study, the effect of the adherend width on the tensile strength and the failure load of Z joints was analyzed both experimentally and numerically using two adhesives with different properties. Atlac™ 580 and Flexsotix™ were used as adhesives, and adherends were prepared with two different composite materials. To identify the mechanical properties of the adhesives, the bulk specimen method was used. Then, the Z joints were prepared using the aforementioned adhesives. The Z joints were subjected to tensile loads in the experiments. The stress analyses were performed using a three-dimensional finite element method (3D FEM). The 3D FEM analyses were performed with ANSYS (10.0). The 3D FEM analyses were performed to investigate the stress distributions in the adhesive layers in the Z joints. The numerical results compared favorably with the experimental results, and were found to be quite reasonable. The results showed that the joint strength increased when the specimen width (b) was increased. To maximize the performance of the joint for either adhesive, b=15mm was found to be the most suitable value for the width.Öğe The effect of overlap length adhesive with bonded in Z type materials(Academic Journals, 2011-09-11) İşcan, Bahattin; Adin, Hamit; Aydın, TurgutThe usage of adhesives as connecting method is increasing rapidly in today world. Many of research, development and engineering have been made to find the most important parameters of adhesion. In this study, stress analysis of bonded Z type that connected with various adhesives has been investigated. The adhesive thickness and overlap non-angle was constant but overlap length and overlap angle were varied. This paper has deal with the effect of overlap length on predicting of failure load of adhesive. An effective method for numerical solution in finite element method (FEM) has been performed in analysis. The FEM code employed was ANSYS(10.0). Experimental results were compared with numerical results and were found quite reasonable.Öğe The investigation of the tensile behaviors of single L-joint type bonded with adhesive and rivet(Wiley-Blackwell, 2018-08) Adin, Hamit; Kurtkan, Ümitn this study, tensile behaviour of single “L” type joints was investigated experimentally and numerically. Aluminium pieces with 2 mm, 3 mm and 4 mm thicknesses were used as joint materials. Overlap lengths were chosen as 10 mm, 15 mm and 20 mm. Joints were executed with two different rivets as steel and aluminium and 3 M 2216 epoxy based adhesive. Experiments were carried out by means of Shimadzu universal testing machine with 5 kN load cell. While the numerical study was carried out, using ANSYS Workbench, finite element analysis program, models were formed with the same properties as experimental works. Results showed that the samples with 20 mm overlap length had the highest strength of all models. Models with steel rivet had higher strength than models with aluminium rivets for all overlap lengths.
