4 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 4 / 4
Öğe Strength and failure analysis of inverse Z joints bonded with Vinylester Atlac 580 and Flexo Tix adhesives(Springer, 2012-11) Adin, Hamit; Turgut, AydınIn this study, the tensile strength and failure loads of the inverse Z joints were analyzed both experimentally and numerically by using two adhesives with different properties under a tensile load. Vinylester Atlac 580 and Flexo Tix were used as adhesives and the joints were prepared with two different composite materials. Initially, the mechanical properties of the adhesives were specified using bulk specimens. Then, the stress analyses were performed using three-dimensional finite element method (3-D FEM) via Ansys (V.10.0.1). The experimental results were compared with the numerical results and they were found quite reasonable. According to the test results, it can be seen that when the adherend thickness is increased, the stress increases as well. The most appropriate value of the adherend thickness is identified as t = 5 mm. Furthermore, it was observed that the lowest failure load was obtained at t = 3 mm the thickness for each specimen.Öğe Numerical investigation of fatigue behaviors of non-patched and patched aluminum pipes(Hibetullah KILIÇ, 2021-06-01) Adin, Hamit; Yıldız, Bilal; Adin, Mehmet ŞükrüIn this study, the fatigue behaviors of non-patched and patched aluminum pipes were investigated numerically. The Finite Element Method was used for fatigue analysis in the study. Finite Element Method was implemented with Ansys Workbench (15.0) program. Al 6063 type aluminum pipe, DP-460 type adhesive and [0/90]2 reinforced angled glass-epoxy composite patch material were used in the analyzes. As a result of the numerical study, it was observed that patch size is an effective parameter in fatigue strength and that quarter-circle and semi-circular composite patches increase the fatigue life. It was also observed in the analyzes that the quarter-circle patched aluminum pipes achieved higher fatigue strength.Öğe The effects of width on the strength of adhesively bonded Z joints subjected to tensile loads(Taylor & Francis, 2012-11-15) Adin, HamitIn this study, the effect of the adherend width on the tensile strength and the failure load of Z joints was analyzed both experimentally and numerically using two adhesives with different properties. Atlac™ 580 and Flexsotix™ were used as adhesives, and adherends were prepared with two different composite materials. To identify the mechanical properties of the adhesives, the bulk specimen method was used. Then, the Z joints were prepared using the aforementioned adhesives. The Z joints were subjected to tensile loads in the experiments. The stress analyses were performed using a three-dimensional finite element method (3D FEM). The 3D FEM analyses were performed with ANSYS (10.0). The 3D FEM analyses were performed to investigate the stress distributions in the adhesive layers in the Z joints. The numerical results compared favorably with the experimental results, and were found to be quite reasonable. The results showed that the joint strength increased when the specimen width (b) was increased. To maximize the performance of the joint for either adhesive, b=15mm was found to be the most suitable value for the width.Öğe Investigation of the effect of different variables on strength of adhesive joints(WILEY, 2014-10-01) Adin, Hamit; Deniz, Mehmet EminIn this article, the tensile strength of different adhesive bonded joints under a tensile load was analyzed numerically. The effects of certain parameters, including the bonding length and bonding ratio, were investigated. For this reason, the epoxy adhesive was used. Joints were prepared with aluminum materials. The stress analyses were employed using the Finite Element Method (FEM). ANSYS (v.14.0.1) FEM tool was utilized to investigate the stress distribution characteristics of aluminum lap joint under tensile loading. Numerical results were found to be quite reasonable. The numerical results show that the influences of variations are very notable when the equivalent stresses are between 18 MPa and 20 MPa. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.
