26 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 10 / 26
Öğe Combustion, performance and emissions of a diesel power generator fueled with biodiesel-kerosene and biodiesel-kerosene-diesel blends(Elsevier, 2017-02-05) Bayındır, Hasan; Işık, Mehmet Zerrakki; Argunhan, Zeki; Yücel, Halit Lütfi; Aydın, HüseyinHigh percentages of biodiesel blends or neat biodiesel cannot be used in diesel engines due to high density and viscosity, and poor atomization properties that lead to some engine operational problems. Biodiesel was produced from canola oil by transesterification process. Test fuels were prepared by blending 80% of the biodiesel with 20% of kerosene (B80&K20) and 80% of the biodiesel with 10% of kerosene and 10% diesel fuel (B80&K10&D10). Fuels were used in a 4 cylinders diesel engine that was loaded with a generator. Combustion, performance and emission characteristics of the blend fuels and D2 in the diesel engine for certain loads of 3.6, 7.2 and 10.8 kW output power and 1500 rpm constant engine speed were experimented and deeply analyzed. It was found that kerosene contained blends had quite similar combustion characteristics with those of D2. Mass fuel consumption and Bscf were slightly increased for blend fuels. HC emissions slightly increased while NOx emissions considerably reduced for blends. It was resulted that high percentages of biodiesel can be a potential substitute for diesel fuel provided that it is used as blending fuel with certain amounts of kerosene.Öğe Investigation of the usability of biodiesel obtained from residual frying oil in a diesel engine with thermal barrier coating(Journals & Books, 2015-04-05) Aydın, Hüseyin; Sayın, Cenk; Aydın, SelmanIn this study, biofuel was produced from residual frying oil of cottonseed and D2, B5 and B100 fuels were prepared in order to use in experiments. These fuels were tested in a single cylinder, four strokes, 3 LD 510 model Lombardini CI engine. Then the top surfaces of the piston and valves were coated with plasma spray coating method by using 100 μm of NiCrAl as lining layer and over this layer the same surfaces were coated with 400 μm of the mixture that consists of %88 ZrO2, %4 MgO and %8 Al2O3. After the coating process, above mentioned fuels were tested in the coated engine. Previously, same fuels had been tested in uncoated engine, at full load and various speeds. Performance, emission and combustion experiments were carried out in coated engine. By coating process, partial increases were observed in power, exhaust manifold temperature and engine noise, while partial decreases were seen in brake specific fuel consumption (Bsfc). Besides, partial reductions were found in carbon monoxide (CO), hydrocarbon (HC) and smoke opacity emissions, but partial increases were observed in nitrogen oxide (NOx) emissions. Cylinder gas pressure values were higher for coated engine. Moreover, heat releases were close to each other in both engines.Öğe Performance and emission evaluation of a CI engine fueled with preheated raw rapeseed oil (RRO)–diesel blends(Journals & Books, 2010-03) Aydın, Hüseyin; Hanbey, HazarMany studies are still being carried out to find out surplus information about how vegetable based oils can efficiently be used in compression ignition engines. Raw rapeseed oil (RRO) was used as blended with diesel fuel (DF) by 50% oil–50% diesel fuel in volume (O50) also as blended with diesel fuel by 20% oil–80% diesel fuel in volume (O20). The test fuels were used in a single cylinder, four stroke, naturally aspirated, direct injection compression ignition engine. The effects of fuel preheating to 100 °C on the engine performance and emission characteristics of a CI engine fueled with rapeseed oil diesel blends were clarified. Results showed that preheating of RRO was lowered RRO’s viscosity and provided smooth fuel flow Heating is necessary for smooth flow and to avoid fuel filter clogging. It can be achieved by heating RRO to 100 °C. It can also be concluded that preheating of the fuel have some positive effects on engine performance and emissions when operating with vegetable oil.Öğe The effects of injection pressure on the engine performance characteristics of a CI engine fueled with canola oil-diesel blends(Energy Education Science and Technology Part A: Energy Science and Research, 2012-01) Aydın, HüseyinThe usage of vegetable oils in diesel engines has some negative effects especially on engine performance. Therefore vegetable oils can not be used as pure form or with high percentages in diesel fuel in unmodified diesel engines. Some of the engine operation conditions should be improved by modifying engine operation systems for this purpose. The effects of injection pressure on engine performance of a diesel engine, by using two different blends of vegetable oil (canola oil) in diesel fuel (DF) having a concentration of 20% (O20) and 50% (O50) vegetable oil, were studied in the present work. The injection pressure was changed from 200 MPa to 220 MPa. Tests were made at fully loaded engine and different speeds of engine operation. In the experiments, the engine power, torque, brake specific fuel consumption (Bsfc), mass fuel consumption rate, brake thermal efficiency and exhaust gas temperature of the test engine have been investigated. Results revealed that the increased injection pressure can significantly promote performance parameters of diesel engine with using vegetable oil without any modification either in oil or in engine itself. The improved results of experiments have been given as graphics in this paper.Öğe Determination of performance and exhaust emissions properties of B75 in a CI engine application(Journals & Books, 2011-09) Aydın, Hüseyin; İlkılıç, CumaliIn this study, performance and exhaust emissions of biodiesel in a compression ignition engine was experimentally investigated. Therefore, biodiesel has been made by transesterification from cotton seed oil and then it was mixed with diesel fuel by 25% volumetrically, called here as B75 fuel. B75 fuel was tested, as alternative fuel, in a single cylinder, four strokes, and air-cooled diesel engine. The effect of B75 and diesel fuels on the engine power, engine torque and break specific fuel consumption were clarified by the performance tests. The influences of B75 fuel on CO, HC, NOx, Smoke opacity, CO2, and O2 emissions were investigated by emission tests. The engine torque and power, for B75 fuel, were lower than that of diesel fuel in range of 2–3%. However, for the B75, specific fuel consumption was higher than that of diesel fuel by approximately 3%. CO2, CO, HC, smoke opacity and NOx emissions of B75 fuel were lower than that of diesel fuel. The experimental results showed that B75 fuel can be substituted for the diesel fuel without any modifications in diesel engines.Öğe Diesel engine applications for evaluation of performance and emission behavior of biodiesel from different oil stocks(Environmental Progress & Sustainable Energy, 2015-05) Aydın, Hüseyin; Behçet, Rasim; İlkılıç, Cumali; İşcan, Bahattin; Aydın, SelmanExtensive researches on alternative fuels have been carried out since the fossil-based fuels are limited. Many of these studies have ever been on the usability of vegetable oils in diesel engines. In the current work, biodiesel were produced from waste fish oil (FOB), hazelnut oil (HOB), rapeseed oil (ROB), and waste cooking oil (WCOB) by transesterification method. The same optimized variables of 6:1 methanol/oil molar ratio (mol/mol), 0.4% sodium methoxide concentration (wt.%), 60°C reaction temperature, 1000 rpm agitation speed and 2 h reaction time conditions were performed for biodiesel production from all kinds of above mentioned oils. Some of the important chemical and physical properties of test fuels were found. Without making blends with diesel fuel, pure biodiesels were used in a diesel engine in order to clarify how their usage effects on engine performance and exhaust emission parameters. When compared with those of diesel fuel, average torque and power were reduced while brake specific fuel consumption was increased for biodiesels. Besides, carbon monoxide (CO), hydrocarbon (HC) emissions were considerably lower for biodiesel usage while oxides of nitrogen (NOx) emissions were higher than that of diesel fuel. Furthermore, emissions of carbon dioxide (CO2) and smoke opacity were reduced for biodiesel usage. Oxygen (O2) contained in the exhaust gases were higher for biodiesels while they contain more oxygen molecules in their structureÖğe Exhaust emissions of a CI engine operated with biodiesel from rapeseed oil(Taylor & Francis, 2011-01-16) Aydın, Hüseyin; İlkılıç, CumaliIn this study, biodiesel was produced from rapeseed oil and was used in a single cylinder, naturally aspirated and direct-injected diesel engine as pure biodiesel (B100) and as a blend with standard diesel fuel by 20% biodiesel to 80% diesel fuel (B20). The diesel engine emissions and some performance parameters were investigated at fully loaded engine conditions. The effects of pure biodiesel and its blend with diesel fuel on emissions of carbon monoxide (CO), nitrogen oxides (NOx), carbon dioxide (CO2), and sulfur dioxide (SO2) were clarified. Results showed that biodiesel fuel is environmentally friendly since it reduced the emissions of CO, SO 2, and CO2 of engines at all speeds. Results also indicated that the pure biodiesel gave about 12% lower power and 20 to 25% higher fuel consumption as compared to diesel. However, the results were almost the same or slightly different from a blend of biodiesel-diesel and petroleum diesel fuel.Öğe Analysis of ethanol RCCI application with safflower biodiesel blends in a high load diesel power generator(Elsevier, 2016-11-15) Işık, Mehmet Zerrakki; Aydın, HüseyinThe effects of RCCI in a diesel power generator by using safflower oil biodiesel-diesel blends were experimentally investigated. Ethanol was premixed as PFI by rates of 30% and 50% of total mass fuel consumption of the engine. Tests were conducted at constant engine speed of 1500 rpm and fixed load 10.8 kW engine power. The purpose of blending biodiesel with diesel is to increase the fuel reactivity of primary fuel in order to easily initiate the combustion. Therefore, test fuels were prepared by blending 10% of the biodiesel with 90% of diesel, 20% of the biodiesel with 80% of diesel and 50% of the biodiesel with 50% of diesel. The most important combustion, performance and emission indicators of the engine under various conditions have been deeply investigated and results have been presented. The ethanol RCCI operation increased peak pressure values especially with using of B50 as high reactivity fuel while combustion was retarded for both RCCI modes. Overall, many indicators of the combustion was improved. Performance parameters were developed. Especially, bsfc was considerably increased. NOx, emissions were considerably decreased while CO and HC emissions were a bit increased.Öğe Analysis of combustion, performance and emission characteristics of a diesel engine using low sulfur tire fuel(Elsevier, 2015-03-01) Aydın, Hüseyin; İlkılıç, CumaliAn alternative fuel for diesel engines was produced from waste vehicle tires by the method of pyrolysis. In order to reduce sulfur content of produced the liquid fuels, during the reaction Ca(OH) 2 was used. Then, H 2 SO 4 were used after the reaction and the sulfur content of the product was reduced by 83.75%. The properties of diesel fuel, low sulfur tire fuel and fuel mixtures of low sulfur tire fuel and diesel fuel were found. Then the prepared fuel blends and diesel fuel were tested in a diesel engine. Performance, combustion and emission parameters of the engine when using each fuel were obtained and comparisons were made with D2 fuel. Power, torque and mean effective pressure, mass fuel consumption, effective efficiency and bscf values presented. Results justify that the performance of the engine slightly lowers by using blends of LSTF. Cylinder pressure and heat release rate values of the test fuels usage were quite similar with those of D2. CO, HC, and smoke emissions were slightly higher while NOx emissions were lower for LSTF blends. All of these results indicate that desulfurized tire fuels with low percentages can be used as alternative fuel in diesel engine.Öğe Investigation of the effects of butanol addition on safflower biodiesel usage as fuel in a generator diesel engine(Elsevier, 2018-06-15) Aydın, Hüseyin; Çelebi, YahyaAs our world demands more and more energy and fossil fuel resources are running out, searches onfindingalternative fuels in internal combustion engines are increasing. Alcohols and biofuels obtained from oils can beused as alternative diesel fuels. The present work investigated the effects ofn-butanol addition to safflowerbiodiesel usage in a diesel engine used for driving an electrical power generator. Safflower biodiesel was ob-tained by using transesterification method. Binary blends of butanol-biodiesel and ternary blends of ultra-lowsulfur diesel-biodiesel–butanol were contained 5%, 10%, and 20% butanol in volume basis. The tests werecarried out on a four-cylinder, four-strokes, and direct-injection diesel engine at half load operation with stableengine speed of 1500 rpm. Experimental test results on combustion characteristics, emission and performance ofthe fuels were investigated. According to test results, formation of heat release rates and in-cylinder pressurecurves were considerably similar and total heat transfer, average gas temperature and mass fraction burned wereslightly changed. The ternary blends showed lower emission and increased brake thermal efficiency up to 1.5%.Besides, average mass fuel consumption was increased up to 5% and brake specific fuel consumption up to 6%.For the other fuels, emission and brake thermal efficiency were deteriorated.
- «
- 1 (current)
- 2
- 3
- »
