Arama Sonuçları
Listeleniyor 1 - 10 / 326
Öğe N-type InP Schottky diodes with organic thin layer: Electrical and interfacial properties(Journal of Vacuum Science & Technology B, 2010-03) Güllü, Ömer; Turut, AbdulmecitThe rectifying junction characteristics of methyl red (MR) organic film on n-type InP substrate have been studied. It has been observed that MR-based structure shows an excellent rectifying behavior and that the MR film increases the effective barrier height by influencing the space charge region of the n-type InP. The barrier height and ideality factor values for this structure have been obtained as 0.75 eV and 1.93 from the forward bias current-voltage characteristics, respectively. By using capacitance-voltage characteristics at 1 MHz, the barrier height and the carrier concentration values have been calculated as 0.93 eV and 5.13×1015 cm−3, respectively. The energy distributions of the interface states and their relaxation times have been determined from the forward bias capacitance-frequency and conductance-frequency characteristics. Moreover, it was seen that both the interface-state density and the relaxation time of the interface states decreased with bias voltage from experimental results.Öğe Investigation of plasma arc cutting parameters with type-2 fuzzy set and system(De Gruyter, 2013-10) Çelik, Yahya Hışman; Özek, Cebeli; Bulut Özek, MüzeyyenThe objective of the present study was it to design a type-2 fuzzy set and system in order to predict surface roughness and hardness depending on the parameters (material thickness, cutting speed, arc voltage and current) of the plasma arc cutting process of S235JR sheet materials. Therefore, some experimental studies were conducted. The experimentally determined data were used to describe the type-2 fuzzy set and system. Type-2 fuzzy set and system was found to be usefull to predict surface roughnes and hardness. According to the obtained values, the best surface roughness and the values closest to the hardness of the raw material were obtained at 1500 mm/min cutting speed, 8 mm material thickness, 115 V arc voltage and 80 A current.Öğe An exergy analysis of a concentric tube heat exchanger using hBN-water nanofluids(Inder Science Publishers, 2021) Budak Ziyadanoğulları, Neşe; Perçin, SüleymanThis study investigated the effects of using nanofluids prepared with hexagonal boron nitride (hBN) nanoparticles on the thermal performance and pressure drop of a concentric tube heat exchanger. Experiments were carried out with water-hBN nanofluids for stable, dispersed, 0.01%, 0.1% and 1% volume concentrations, at different flow rates and Reynolds numbers under parallel and counter-flow conditions. When the experimental results were examined, the exergy loss was higher in the parallel-flow heat exchanger compared to the counter-flow heat exchanger. The highest exergy loss value was obtained for distilled water at the highest Reynolds number (Re = 8,700) for parallel flow operation at 170 W. The exergy loss of water at the highest Reynolds number (Re = 8,700) for parallel flow operation increased by 15.7%, 24.8% and 49.8% for hBN-water concentrations of 0.01%, 0.1% and 1%, respectively. Exergy loss of water at the highest Reynold number (Re = 8,700) for counter flow operation increased by 11.3%, 17.3% and 29.2% for hBN-water concentrations of 0.01%, 0.1% and 1%, respectively. When evaluating the exergy analysis of the system, exergy losses due to pressure drops were negligible for both flows (parallel and counter).Öğe The effect of Plantago major Linnaeus on serum total sialic acid, lipid-bound sialic acid, some trace elements and minerals after administration of 7,12-dimethylbenz(a)anthracene in rats(SAGE, 2012-04) Oto, Gökhan; Ekin, Suat; Özdemir, Hülya; Levent, Abdulkadir; Berber, İsmetThe present study was designed to evaluate the effect of Plantago major Linnaeus (PM) extract on serum total sialic acid (TSA), lipid-bound sialic acid (LSA), some trace elements (copper (Cu), zinc (Zn) and iron) and mineral levels (magnesium, calcium and sodium) in Wistar albino rat administrated 7,12-dimethylbenz(a)anthracene (DMBA). Rats were divided into three equal groups (n = 6). Group I comprised the control group, group II was treated with DMBA (100 mg/kg, single dose) and group III was treated with DMBA (100 mg/kg single dose) and aqueous extract of PM 100 mg/kg/day for 60 days. After 60 days, statistical analyses showed that TSA and LSA levels in DMBA and DMBA + PM groups were significantly higher compared to the control group (TSA: p < 0.01, p < 0.05; LSA: p < 0.05, p < 0.05, respectively). Serum Zn levels were decreased in subjects treated with DMBA (p < 0.01) and DMBA + PM (p < 0.05) compared to the control group values. Serum Cu levels were increased in DMBA group and PM-treated group compared to the control group values. The results of this investigation showed that the levels of TSA and LSA changed significantly, which are sensitive markers for detecting the toxic effects of DMBA. On the other hand, observed decline in Zn levels in rats from DMBA + PM group might be due to decreased generation of free radicals and oxidative stress. Results from this study suggest that PM may be partially effective in preventing carcinogenesis initiated by environmental carcinogen DMBA.Öğe Numerical and experimental investigation of solar chimney power plant system performance(Taylor & Francis, 2020-03-15) Karakaya, Hakan; Durmuş, Aydın; Avcı, Ali SerkanA prototype of a solar chimney power plant was performed by modeling in this study. The performed prototype was experimentally confirmed. Temperature, velocity, and radiation values were measured to actualize the confirmation. Experimental data that were obtained to determine the performance of solar chimney whose prototype was actualized by the help of measured values were computationally analyzed. The geometry of a solar chimney in the analysis was bidimensionally (2D) drawn on an axis of symmetry. The numerical simulation was analyzed with computational fluid dynamics (CFD) method. Since analysis results show that there is turbulent flow in system (RNG), k-ɛ turbulence model was used. Continuity, momentum, and energy equations were applied to the solar chimney system via the finite volume method. Moreover, DO (discrete ordinates) model was inserted in analysis to evaluate the radiation effect in the collector area. In addition to all these, correlation results between SPSS 17 statistics program and data obtained were evaluated. Finally, with reference to the comparison between numerical and experimental results, data obtained and numerical data are close to each other; the prototype is applicable to the real systems.Öğe Combustion, performance and emissions of a diesel power generator fueled with biodiesel-kerosene and biodiesel-kerosene-diesel blends(Elsevier, 2017-02-05) Bayındır, Hasan; Işık, Mehmet Zerrakki; Argunhan, Zeki; Yücel, Halit Lütfi; Aydın, HüseyinHigh percentages of biodiesel blends or neat biodiesel cannot be used in diesel engines due to high density and viscosity, and poor atomization properties that lead to some engine operational problems. Biodiesel was produced from canola oil by transesterification process. Test fuels were prepared by blending 80% of the biodiesel with 20% of kerosene (B80&K20) and 80% of the biodiesel with 10% of kerosene and 10% diesel fuel (B80&K10&D10). Fuels were used in a 4 cylinders diesel engine that was loaded with a generator. Combustion, performance and emission characteristics of the blend fuels and D2 in the diesel engine for certain loads of 3.6, 7.2 and 10.8 kW output power and 1500 rpm constant engine speed were experimented and deeply analyzed. It was found that kerosene contained blends had quite similar combustion characteristics with those of D2. Mass fuel consumption and Bscf were slightly increased for blend fuels. HC emissions slightly increased while NOx emissions considerably reduced for blends. It was resulted that high percentages of biodiesel can be a potential substitute for diesel fuel provided that it is used as blending fuel with certain amounts of kerosene.Öğe Investigation of low velocity impact behaviors of honeycomb sandwich composites(SpringerLink, 2018-08-09) Topkaya, Tolga; Solmaz, Murat YavuzHoneycomb sandwich composites are used as significant structural members in advanced engineering applications. Thus, it is critical to determine how they behave under impact loading, in addition to other loads. In this study, low velocity impact loading behaviors of honeycomb sandwich composites were experimentally investigated. Almost all of the design parameters of honeycomb sandwich composites were investigated. The results indicated that the core thickness of honeycomb had no effect on the strength of the composite, and the parameter influencing the impact behavior of the specimen the most was the face sheet thickness. When the face sheet thickness of the specimen was increased, the most apparent strength increase was observed in the models using carbon fiber-reinforced composite face sheets. For all face sheet types subject to impact energy of 10 Joules, the upper face sheets of 0.5 mm-thick specimens were perforatedÖğe Hardness and wear behaviours of al matrix composites and hybrid composites reinforced with B 4 C and SiC(Springer Nature, 2019-01-15) Çelik, Yahya Hışman; Kılıçkap, ErolThe conversion into the desired shape of the metal powders using Powder Metallurgy (PM) method enables economically mass productions. This case allows producing parts with complex and high dimensional accuracy with no machining. In this study the composites and hybrid composites with Al matrix were produced using PM method with different ratios B4C and SiC. Microhardness and wear experiments of the produced composites were investigated. Wear experiments were performed at a constant speed of 0.5 m/s, application loads of 5, 10 and 15 N and sliding distances of 250, 500, and 750 m. Then, SEM images of composites and hybrid composites were captured. The increase of the reinforcement ratio in the composites contributed to the increase of the hardness. The highest hardness value was computed as 58.7 HV from 16% B4C reinforced composite. In addition, the increase in the reinforcement ratio contributed to the increase of the wear resistance. The increase in the load and sliding distance also increased the wear. The minimum weight loss was calculated as 18 mg from 5 N load, 250 m sliding distance and 16% SiC reinforced composite.Öğe A novel approach for spam email detection based on shifted binary patterns(Wiley-Blackwell, 2016-01-11) Kaya, Yılmaz; Ertuğrul, Ömer FarukAdvances in communication allow people flexibility to communicate in various ways. Electronic mail (email) is one of the most used communication methods for personal or business purposes. However, it brings one of the most tackling issues, called spam email, which also raises concerns about data safety. Thus, the requirement of detecting spams is crucial for keeping the users safe and saving them from the waste of time while tackling those issues. In this study, an effective approach based on the probability of the usage of the characters that has similar orders with respect to their UTF-8 value by employing shifted one-dimensional local binary pattern (shifted-1D-LBP) was used to extract quantitative features from emails for spam email detection. Shifted-1D-LBP, which can be described as an ordered set of binary comparisons of the center value with its neighboring values, is a content-based approach to spam detection with low-level information. To validate the performance of the proposed approach, three benchmark corpora, Spamassasian, Ling-Spam, and TREC email corpuses, were used. The average classification accuracies of the proposed approach were 92.34%, 92.57%, and 95.15%, respectively. Analysis and promising experimental results indicated that the proposed approach was a very competitive feature extraction method in spam email filtering.Öğe Türkistan’dan Tunceli’ye kurban inancı(Geleneksel Yayıncılık, 2017) Arslan, YusufToplumdan topluma kurbana yüklenen anlam, kurban kesim şekli, kurban sunuları değişiklik gösterse de, çoğunlukla her dinde ve gelenekte kurban, günahlardan arınma, tövbe, şükür gibi amaçlarla yapılmaktadır. 4000 yıllık bir tarihe sahip olan Türklerin gelenekleri incelendiğinde, kurban kesme ritüelinin eskiden beri sürdürüldüğü anlaşılmaktadır. İslamiyet’e dâhil olduktan sonra Türklerin kurban ritüellerinde bazı değişimler yaşanmıştır. Bazı ritüeller uygulamadan kalkarken bazıları yaşatılmıştır. Örneğin, eski Türklerde kurbanların başında gelen at, İslamiyet ile birlikte yerini koç, koyun, keçi, sığır gibi hayvanlara bırakmış ve at kurban etme geleneği unutulmuştur. Bununla birlikte, Şaman ayinlerinde kurban kesilmesi, mum yakılması geleneğinin Alevilerin cem ritüeli vesilesiyle olduğu gibi yaşatıldığı görülmektedir. Günümüzde, Aleviler arasında, eski Türk gelenek, görenek ve dinine ait motifler canlı şekilde izlenebilmektedir. Örneğin, Aleviler İslam’ı benimsemiş olmalarına karşın, İslam ile beraber eski Türklerin şaman/kam inancı, kopuz eşliğinde ibadet etme, sema, kadın/erkek bir arada ibadet etme, atalar kültü, dağ, ağaç ve nehirlere kutsallık atfetme biçimindeki inançlarını terk etmemişlerdir. İbadet dillerini de olduğu şekliyle, yani Türkçe olarak korumuşlardır. Alevilerin kurban ritüelleri, kimi değişimlere uğramışsa da, eski Türklerdeki birçok ritüeli bünyesinde korumuştur ve Aleviler yüzyıllardır eski Türk geleneklerindeki şekliyle kurbanlarını kesmişlerdir. Bu makalede, eski Türklerdeki kurban ritüelleriyle Tunceli Alevilerinin halk inançlarındaki kurban ritüeli karşılaştırılmış, benzerliklerin tespitine çalışılmıştır. Araştırma, nitel araştırma yöntemine göre gerçekleştirilmiştir. Araştırmanın verileri, 2015-2016 yıllarında Tunceli ve ilçelerinde, ziyaret yerlerinde yapılan yüz yüze mülakatlardan elde edilmiştir. Toplam görüşmeci sayısı sekiz olup görüşmeciler Tunceli il nüfusuna kayıtlıdır. Araştırmanın verileri, eski Türklerin kurban pratikleri ile Tunceli Alevilerinin kurban pratiklerinin dayandığı ortak bir geleneksel temel yapı olduğunu göstermiştir. Bir başka ifadeyle, Alevilerin kurban sunu/sungusu pratiklerinde, eski Türk geleneklerinin önemli oranda korunmuş olduğu anlaşılmıştır.
