23 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 10 / 23
Öğe An exergy analysis of a concentric tube heat exchanger using hBN-water nanofluids(Inder Science Publishers, 2021) Budak Ziyadanoğulları, Neşe; Perçin, SüleymanThis study investigated the effects of using nanofluids prepared with hexagonal boron nitride (hBN) nanoparticles on the thermal performance and pressure drop of a concentric tube heat exchanger. Experiments were carried out with water-hBN nanofluids for stable, dispersed, 0.01%, 0.1% and 1% volume concentrations, at different flow rates and Reynolds numbers under parallel and counter-flow conditions. When the experimental results were examined, the exergy loss was higher in the parallel-flow heat exchanger compared to the counter-flow heat exchanger. The highest exergy loss value was obtained for distilled water at the highest Reynolds number (Re = 8,700) for parallel flow operation at 170 W. The exergy loss of water at the highest Reynolds number (Re = 8,700) for parallel flow operation increased by 15.7%, 24.8% and 49.8% for hBN-water concentrations of 0.01%, 0.1% and 1%, respectively. Exergy loss of water at the highest Reynold number (Re = 8,700) for counter flow operation increased by 11.3%, 17.3% and 29.2% for hBN-water concentrations of 0.01%, 0.1% and 1%, respectively. When evaluating the exergy analysis of the system, exergy losses due to pressure drops were negligible for both flows (parallel and counter).Öğe Hardness and wear behaviours of al matrix composites and hybrid composites reinforced with B 4 C and SiC(Springer Nature, 2019-01-15) Çelik, Yahya Hışman; Kılıçkap, ErolThe conversion into the desired shape of the metal powders using Powder Metallurgy (PM) method enables economically mass productions. This case allows producing parts with complex and high dimensional accuracy with no machining. In this study the composites and hybrid composites with Al matrix were produced using PM method with different ratios B4C and SiC. Microhardness and wear experiments of the produced composites were investigated. Wear experiments were performed at a constant speed of 0.5 m/s, application loads of 5, 10 and 15 N and sliding distances of 250, 500, and 750 m. Then, SEM images of composites and hybrid composites were captured. The increase of the reinforcement ratio in the composites contributed to the increase of the hardness. The highest hardness value was computed as 58.7 HV from 16% B4C reinforced composite. In addition, the increase in the reinforcement ratio contributed to the increase of the wear resistance. The increase in the load and sliding distance also increased the wear. The minimum weight loss was calculated as 18 mg from 5 N load, 250 m sliding distance and 16% SiC reinforced composite.Öğe Finite element analysis of the stress distributions in peri-implant bone in modified and standard-threaded dental implants(Taylor & Francis, 2016-01) Topkaya, Tolga; Dündar, Serkan; Solmaz, Murat Yavuz; Yaman, Ferhan; Atalay, Yusuf; Saybak, Arif; Asutay, Fatih; Çakmak, ÖmerThe aim of this study was to examine the stress distributions with three different loads in two different geometric and threaded types of dental implants by finite element analysis. For this purpose, two different implant models, Nobel Replace and Nobel Active (Nobel Biocare, Zurich, Switzerland), which are currently used in clinical cases, were constructed by using ANSYS Workbench 12.1. The stress distributions on components of the implant system under three different static loadings were analysed for the two models. The maximum stress values that occurred in all components were observed in FIII (300 N). The maximum stress values occurred in FIII (300 N) when the Nobel Replace implant is used, whereas the lowest ones, in the case of FI (150 N) loading in the Nobel Active implant. In all models, the maximum tensions were observed to be in the neck region of the implants. Increasing the connection between the implant and the bone surface may allow more uniform distribution of the forces of the dental implant and may protect the bone around the implant. Thus, the implant could remain in the mouth for longer periods. Variable-thread tapered implants can increase the implant and bone contact.Öğe Experimental investigation of solar stills integrated with solar water heating collectors(Türk Isı Bilimi ve Tekniği Derneği, 2017-10-31) Argunhan, Zeki; El, Emin; Yıldız, Cengiz; Çakmak, GülşahSolar still is a more practical way of obtaining clean water. In this study, we aimed to improve the efficiency of solar still systems and obtain distilled water at the same time. For this purpose, 5 different solar still systems were designed. Type 1; conventional solar still, Type 2; conventional solar still integrated with solar water heating collector and run via natural convection, Type 3; conventional solar still integrated with solar water heating collector and tubular heat exchanger and run via natural convection, Type 4; conventional solar still placed with plate heat exchanger and integrated with solar water heating collector and run via natural convection, Type 5; conventional solar still placed with plate heat exchanger and integrated with solar water heating collector and run via forced convection. In this study, the experiments were carried out on the parameters influencing the performance, the amount of distilled water obtained, and the efficiency of experiment settings designed in different types; and finally the results were presented. The amount of distilled water and efficiency of conventional solar still were 2389 ml and 51.47%, respectively. Maximum total amount of water and efficiency from natural convection systems were obtained from Type 4, and the values calculated were found as to be 5788 ml and 55.91%. Maximum amount of distilled water and the efficiency were obtained by utilizing forced convection system were found as to be 6068 ml and 58.99%, respectively.Öğe The characteristic diode parameters in Ti/p-InP contacts prepared by DC sputtering and evaporation processes over a wide measurement temperature(World Scientific, 2017-06) Ejderha, Kadir; Asubay, Sezai; Yıldırım, Nezir; Güllü, Ömer; Türüt, Abdülmecit; Abay, BahattinThe titanium/p-indium phosphide (Ti/p-InP) Schottky diodes (SDs) have been prepared by thermal evaporation and DC magnetron sputtering deposition. Then, their current-voltage (I-V) characteristics have been measured in the sample temperature range of 100-400K with steps of 20K. The characteristic parameters of both Ti/p-InP SDs have been compared with each other. The barrier height (BH) values of 0.824 and 0.847 at 300K have been obtained for the sputtered and the evaporated SDs, respectively. This low BH value for the sputtered SD has been attributed to some defects introduced by the sputtered deposition technique over a limited depth in to the p-type substrate. The BH of the evaporated and sputtered diodes has decreased with the standard deviations of 58 and 64mV obeying to double-Gaussian distribution (GD) in 220-400K range, respectively, and it has seen a more sharper reduction for the BHs with the standard deviations of 93 and 106 mV in 100-220K range. The Richardson constant values of 89.72 and 53.24A(Kcm)-2 (in 220-400K range) for the evaporated and sputtered samples, respectively, were calculated from the modified ln(I0/T2)-q2σs2/2k2T2 vs (kT)-1 curves by GD of the BHs. The value 53.24A(Kcm)-2 for the sputtered sample in high temperatures range is almost the same as the known Richardson constant value of 60A(Kcm)-2 for p-type InP.Öğe A generalization of the Katzman-Zhang algorithm(Elsevier, 2021-03) Yeşil, MehmetIn this paper, we study the notion of special ideals. We generalize the results on those as well as the algorithm obtained for finite dimensional power series rings by Mordechai Katzman and Wenliang Zhang to finite dimensional polynomial rings.Öğe Geochemical features of the Menteşe Formation dolostones (Rhaetian) in the Karacahisar-Kasımlar area (Isparta-Turkey)(SpringerLink, 2018-08) Dinç, Salih; Özkan, Ali MüjdatThe purpose of this study is to determine the geochemical characteristics of the Menteşe dolostones (Rhaetian) in the west Taurus Mountains, Turkey. The isotope characteristics of the Menteşe dolostones show a variation in the δ18O values of the dolomites between + 1.35 and − 2.72‰ (VPDB) and a variation in the δ13C values of the dolomites between + 1.6 and + 3.33‰ (VPDB). Most of the Menteşe dolostone samples have positive oxygen isotope values; others have weak negative isotope values, which indicate early diagenetic development. In addition, oxygen, carbon, and strontium isotopes and trace element analyses suggest that these dolostones were probably resulted from insignificant recrystallizaion process than chemically similar fluids. Furthermore, Mn/Sr values of the Menteşe dolostones indicate that there is no significant diagenetic alteration. The total REE contents of the Menteşe Formation dolostones display a strong positive correlation with Si, Al, Fe, K, Ti, Ba, Rb and negative correlation with Mg, hence REE content is associated with in the first degree titanium-bearing minerals (probably sphene, rutile, anatase), second degree phosphate (apatite), and barium and rubidium-bearing minerals (probably barite). Ce anomalies versus Nd concentrations of the Menteşe dolostone samples indicate that these dolostones are formed in an anoxic environment. In addition, the K/Rb ratios of the Menteşe dolostones are not exposed to any metamorphism and indicate some diagenetic alteration. Calculated temperature values using δ18O values of the Menteşe dolostones yield precipitation temperatures of 17 to 42 °C, and suggest burial depths of 67 to 900 m. Sources of magnesium for dolomitization of the Menteşe Formation carbonates were most likely fluids from seawater and/or diagenetic brines (slightly modified seawater). The Menteşe dolostones formed as early diagenetic (Rhaetian to Cenomanian) in shallow burial areas at lower temperatures than seawater and/or diagenetic brines (slightly modified seawater).Öğe A novel approach for extracting ideal exemplars by clustering for massive time-ordered datasets(TÜBİTAK, 2017-07-30) Ertuğrul, Ömer FarukThe number and length of massive datasets have increased day by day and this yields more complex machine learning stages due to the high computational costs. To decrease the computational cost many methods were proposed in the literature such as data condensing, feature selection, and filtering. Although clustering methods are generally employed to divide samples into groups, another way of data condensing is by determining ideal exemplars (or prototypes), which can be used instead of the whole dataset. In this study, first the efficiency of traditional data condensing by clustering approach was confirmed according to obtained accuracies and condensing ratios in 9 different synthetic or real batch datasets. This approach was then improved to be employed in time-ordered datasets. In order to validate the proposed approach, 23 different real time-ordered datasets were used in experiments. Achieved mean RMSEs were 0.27 and 0.29 by employing the condensed (mean condensed ratio was 97.17%) and the whole datasets, respectively. Obtained results showed that higher accuracy rates and condensing ratios were achieved by the proposed approach.Öğe Analysis of interface states of Al/DNA/p-Si MIS photovoltaic structures with DNA biomolecules using the conductance technique(Taylor & Francis, 2017-03-29) Güllü, ÖmerIn this study, we report on the calculation of interface charge distribution of metal–interlayer–semiconductor (MIS) photovoltaic diodes containing DNA biomolecules and Si semiconductor based on the conductance technique. DNA biofilms were deposited at room temperature using a simple cast method on p-type Si. Interface parameters of the Al/DNA/p-Si structures were investigated by using capacitance–voltage (C–V) and conductance–voltage (G–V) measurements as a function of frequency. The distributions of interfacial charge states and the trap relaxation times were reported. Also, photoelectric and photocapacitance properties of the diode were measured at room temperature.Öğe Separation, optimization, and quantification of cytokinins by a recently developed amide-embedded stationary phase(Taylor & Francis, 2017-07-06) Aral, Hayriye; Haşimi, Duygu; Aral, Tarık; Levent, Abdulkadir; Ziyadanoğulları, BerrinIn this study, some plant growth regulators known as cytokinins [kinetin (K), zeatin (Z), thidiazuron (TDZ), benzylaminopurine (BAP), and dimethylallylaminopurine (AAP)] were separated by HPLC using an amide-embedded mixed-mode stationary phase which was synthesized by Aral et al. in recent years. The effect of mobile phase content, mobile phase pH, buffer concentration, and temperature on separation process was studied. In addition, a quantitative determination of cytokinins from Salvia limbata extract was studied, and some validation parameters such as limit of detection (LOD), limit of quantification (LOQ), and relative standard deviation (RSD) were calculated as a range of 0.03–0.1, 0.1–0.26 mg/L, and 0.03–0.08, respectively.
- «
- 1 (current)
- 2
- 3
- »
