15 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 10 / 15
Öğe The comparison of engine performance and exhaust emission characteristics of sesame oil-diesel fuel mixture with diesel fuel in a direct injection diesel engine(Elsevier, 2008-01-09) Altun, Şehmus; Bulut, Hüsamettin; Öner, CengizThe use of vegetable oils as a fuel in diesel engines causes some problems due to their high viscosity compared with conventional diesel fuel. Various techniques and methods are used to solve the problems resulting from high viscosity. One of these techniques is fuel blending. In this study, a blend of 50% sesame oil and 50% diesel fuel was used as an alternative fuel in a direct injection diesel engine. Engine performance and exhaust emissions were investigated and compared with the ordinary diesel fuel in a diesel engine. The experimental results show that the engine power and torque of the mixture of sesame oil-diesel fuel are close to the values obtained from diesel fuel and the amounts of exhaust emissions are lower than those of diesel fuel. Hence, it is seen that blend of sesame oil and diesel fuel can be used as an alternative fuel successfully in a diesel engine without any modification and also it is an environmental friendly fuel in terms of emission parameters.Öğe Aspir ve kanola biyodizeli kullanımının egzoz emisyonu ve motor performansına etkilerinin incelenmesi(Küresel Mühendislik Çalışmaları Dergisi, 2016-04-01) Aydın, Hüseyin; Işık, Mehmet Zerrakki; Ziyadanoğulları Budak, Neşe; Oktay, Hasan; Bayındır, Hasan; Yücel, Halit LutfiBiodiesel fuel, which can be produced from crude or waste vegetable oil, is an important alternative renewable fuel for diesel engines. Particularly the use of vegetable oils for diesel engines has found an important place in several surveys. Biodiesel can be used alone, or blended with petrodiesel in any proportions. Biodiesel is suitable for usage at conventional diesel engines without modification. In this study, canola and safflower oil biodiesel methyl is realized by using the esterification method.. The produced biodiesels were blended in %(50) (in volume) with diesel fuel. The blends were tested in a four cycle, four cylinder Diesel engine. The effects of biodiesel addition to Diesel No. 2 on the performance and emissions of the engine were examined at full load. The resulting performance values were found to be similar to diesel fuel. In general, specific fuel consumption of biodiesel is higher than diesel at all engine loads. Significant difference between the exhaust temperature is not determined. AB50 biodiesel compared to diesel HC emissions at high loads began to decline. NOx, CO2 and O2 emissions ratio has increased at high loads for Biodiesel fuels. Experimental results showed that the produced biodiesels can be partially substituted for the diesel fuel at most operating conditions in terms of the performance parameters and emissions without any engine modification and preheating of the blends.Öğe Performance and emission analysis of cottonseed oil methyl ester in a diesel engine(Elsevier, 2010-03) Aydın, Hüseyin; Bayındır, HasanIn this study, performance and emissions of cottonseed oil methyl ester in a diesel engine was experimentally investigated. For the study, cottonseed oil methyl ester (CSOME) was added to diesel fuel, numbered D2, by volume of 5%(B5), 20%(B20), 50%(B50) and 75%(B75) as well as pure CSOME (B100). Fuels were tested in a single cylinder, direct injection, air cooled diesel engine. The effects of CSOME-diesel blends on engine performance and exhaust emissions were examined at various engine speeds and full loaded engine. The effect of B5, B20, B50, B75, B100 and D2 on the engine power, engine torque, bsfc's and exhaust gasses temperature were clarified by the performance tests. The influences of blends on CO, NOx, SO2 and smoke opacity were investigated by emission tests. The experimental results showed that the use of the lower blends (B5) slightly increases the engine torque at medium and higher speeds in compression ignition engines. However, there were no significant differences in performance values of B5, B20 and diesel fuel. Also with the increase of the biodiesel in blends, the exhaust emissions were reduced. The experimental results showed that the lower contents of CSOME in the blends can partially be substituted for the diesel fuel without any modifications in diesel engines.Öğe Performance and emission evaluation of a CI engine fueled with preheated raw rapeseed oil (RRO)–diesel blends(Journals & Books, 2010-03) Aydın, Hüseyin; Hanbey, HazarMany studies are still being carried out to find out surplus information about how vegetable based oils can efficiently be used in compression ignition engines. Raw rapeseed oil (RRO) was used as blended with diesel fuel (DF) by 50% oil–50% diesel fuel in volume (O50) also as blended with diesel fuel by 20% oil–80% diesel fuel in volume (O20). The test fuels were used in a single cylinder, four stroke, naturally aspirated, direct injection compression ignition engine. The effects of fuel preheating to 100 °C on the engine performance and emission characteristics of a CI engine fueled with rapeseed oil diesel blends were clarified. Results showed that preheating of RRO was lowered RRO’s viscosity and provided smooth fuel flow Heating is necessary for smooth flow and to avoid fuel filter clogging. It can be achieved by heating RRO to 100 °C. It can also be concluded that preheating of the fuel have some positive effects on engine performance and emissions when operating with vegetable oil.Öğe The effects of injection pressure on the engine performance characteristics of a CI engine fueled with canola oil-diesel blends(Energy Education Science and Technology Part A: Energy Science and Research, 2012-01) Aydın, HüseyinThe usage of vegetable oils in diesel engines has some negative effects especially on engine performance. Therefore vegetable oils can not be used as pure form or with high percentages in diesel fuel in unmodified diesel engines. Some of the engine operation conditions should be improved by modifying engine operation systems for this purpose. The effects of injection pressure on engine performance of a diesel engine, by using two different blends of vegetable oil (canola oil) in diesel fuel (DF) having a concentration of 20% (O20) and 50% (O50) vegetable oil, were studied in the present work. The injection pressure was changed from 200 MPa to 220 MPa. Tests were made at fully loaded engine and different speeds of engine operation. In the experiments, the engine power, torque, brake specific fuel consumption (Bsfc), mass fuel consumption rate, brake thermal efficiency and exhaust gas temperature of the test engine have been investigated. Results revealed that the increased injection pressure can significantly promote performance parameters of diesel engine with using vegetable oil without any modification either in oil or in engine itself. The improved results of experiments have been given as graphics in this paper.Öğe Yağ alkolleri ve biyodizel karışımlarının bir dizel motorda yanma ve performans parametrelerine etkilerinin deneysel ve yapay sinir ağları ile optimizasyonu(Batman Üniversitesi Lisansüstü Eğitim Enstitüsü, 2023-07-06) Deviren, Halis; Aydın, HüseyinBu çalışmada, aspir tohumlarından farklı yöntemlerle yağ ekstrakte edilmiş ve ekstrakte edilen aspir tohumu yağı (ATY) transesterifikasyon prosesi ile biyodizele (B100)’e sentezlenmiştir. B100, dizel yakıt (DF) ve farklı ağır alkoller (AA)’ler belli oranlarda harmanlanarak elde edilen yakıtların motor performansı, emisyonları ve yanma parametreleri incelenmiştir. Yanma parametrelerinin deneysel sonuçları yapay sinir ağları (YSA) ile tahmin edilmiştir. Ekstraksiyon yöntemleri arasında maksimum yağ elde etme verimliliği sokslet ekstraksiyon yöntemi ile %32.49 olarak gerçekleşmiştir. ATY’nin yağ asidi bileşimleri sırasıyla %30.9 ve %56.4 civarında C18:1 ve C18:2’dir. ATY’nin biyodizele sentezlenmesinde alkol/yağ molar oranı 4.799/1 olarak hesaplanmıştır. Biyodizelin sentezi spektroskopik yöntemler ile doğrulanmıştır. 1H NMR ile yağ asidi metil esterlere (YAME)’lere dönüşüm %95.23 olarak hesaplanmıştır. Gerçekleştirilen analizler neticesinde sentezlenen biyodizelin ASTM-D6751 ve EN-14214 standartlarını karşıladığı görülmüştür. Testlerde DF50DE50 yakıtı DF’den sonra en düşük fren özgül yakıt tüketimi (FÖYT) ve fren özgül enerji tüketimi (FÖET) ile sonuçlanmışken fren termal verimliliği (FTV) bakımından ise DF’den sonra en yüksek olan yakıttır. DF50HE50 yakıtı ile en yüksek egzoz gazı sıcaklığı (EGS) elde edilmişken, en düşük EGS ise DF50B25HE25 yakıtı ile elde edilmiştir. B100’ün üretmiş olduğu NOx emisyonu DF’ye göre yüksektir. Düşük NOx emisyonu ise dekanolün olduğu karışımlar tarafından üretilmiştir. B100’ün üretmiş olduğu CO emisyonu DF’nin üretmiş olduğundan daha yüksektir. DF50B50’nin üretmiş olduğu CO emisyonları tekli ve ikili yakıt karışımlarının üretmiş olduklarına kıyasla daha düşüktür. DF’nin üretmiş olduğu is emisyonu ise bütün test yakıtlarının üretmiş olduğundan daha yüksektir. DF50OC50 artan yükler ile yüksek silindir basınçları (SB)’ler oluştururken, en büyük SB DF50HE50 yakıtınındır. DF50HE50 yakıtının net ısı salımı hızı (NISH) en yüksektir. B100’ün basınç artış oranı (BAO), DF yakıtından yüksek iken DF50B50 yakıtının BAO’sı tekli yakıtlarınkine göre daha düşük olmuştur. Üçlü yakıt karışımlarının BAO’sı ikili yakıt karışımlarına göre düşüktür. Yanma verilerinin YSA ile tahmini ortalama kare hatası (MSE) değerleri doğrultusunda oldukça başarılı olduğu görülmüştür.Öğe Exhaust emissions of methanol and ethanol-unleaded gasoline blends in a spark ignition engine(VINCA Institute of Nuclear Sciences, 2013) Altun, Şehmus; Öztop, Hakan Fehmi; Öner, Cengiz; Varol, YasinIn this study, the effect of unleaded gasoline and unleaded gasoline blended with 5% and 10% of ethanol or methanol on the performance and exhaust emissions of a spark-ignition engine were experimentally investigated. The engine tests were performed by varying the engine speed between 1000 and 4000 rpm with 500 rpm period at three-fourth throttle opening position. The results showed that brake specific fuel consumption increased while brake thermal efficiency, emissions of carbon monoxide and hydrocarbon decreased with methanol-unleaded gasoline and ethanol-unleaded gasoline blends. It was found that a 10% blend of ethanol or methanol with unleaded gasoline works well in the existing design of engine and parameters at which engines are operating.Öğe Exhaust emissions of a CI engine operated with biodiesel from rapeseed oil(Taylor & Francis, 2011-01-16) Aydın, Hüseyin; İlkılıç, CumaliIn this study, biodiesel was produced from rapeseed oil and was used in a single cylinder, naturally aspirated and direct-injected diesel engine as pure biodiesel (B100) and as a blend with standard diesel fuel by 20% biodiesel to 80% diesel fuel (B20). The diesel engine emissions and some performance parameters were investigated at fully loaded engine conditions. The effects of pure biodiesel and its blend with diesel fuel on emissions of carbon monoxide (CO), nitrogen oxides (NOx), carbon dioxide (CO2), and sulfur dioxide (SO2) were clarified. Results showed that biodiesel fuel is environmentally friendly since it reduced the emissions of CO, SO 2, and CO2 of engines at all speeds. Results also indicated that the pure biodiesel gave about 12% lower power and 20 to 25% higher fuel consumption as compared to diesel. However, the results were almost the same or slightly different from a blend of biodiesel-diesel and petroleum diesel fuel.Öğe Experimental investigation of the effects of diesel-like fuel obtained from waste lubrication oil on engine performance and exhaust emission(Journals & Books, 2010-10) Argunhan, Zeki; Yumrutaş, Recep; Arpa, OrhanIn this study, effects of diesel-like fuel (DLF) on engine performance and exhaust emission are investigated experimentally. The DLF is produced from waste engine lubrication oil purified from dust, heavy carbon soot, metal particles, gum-type materials and other impurities. A fuel production system mainly consisting of a waste oil storage tank, filters, a reactor, oil pump, a product storage tank, thermostats and control panel is designed and manufactured. The DLF is produced by using the system and applying pyrolitic distillation method. Characteristics, performance and exhaust emissions tests of the produced DLF are carried out at the end of the production. The characteristic tests such as density, viscosity, flash point, heating value, sulfur content and distillation of the DLF sample are performed utilizing test equipments presented in motor laboratory of Mechanical Engineering Department, University of Gaziantep, Turkey. Performance and exhaust emission tests for the DLF are performed using diesel test engine. It is observed from the test results that about 60 cc out of each 100 cc of the waste oil are converted into the DLF. Characteristics and distillation temperatures of the DLF are close to those values of a typical diesel fuel sample. It is observed that the produced DLF can be used in diesel engines without any problem in terms of engine performance. The DLF increases torque, brake mean effective pressure, brake thermal efficiency and decreases brake specific fuel consumption of the engine for full power of operation.Öğe Usage of methyl ester produced from waste grape and Mn additive as alternative diesel fuel(Petru Maior” University of Tîrgu Mureş, 2017-01) Aydın, Hüseyin; Hanbey, Hazar; Uyar, Mahmut; Sap, EmineIn this study, methyl ester was produced from waste grape pulp sources. The produced methyl ester was mixed with diesel in different proportions, and was tested for engine performance and emission. It was found that with increasing biodiesel content, the specific fuel consumption and exhaust temperature have increased partially, while the CO, HC and smoke emissions decreased significantly. Additionally, in the scope of this study, dodecanol, propylene glycol and Mn based additives were added to fuel B50 to improve the emission and engine performance values. With the presence of additives, an increase in the exhaust temperature was observed, while a decrease in the specific fuel consumption, CO, HC, and smoke emissions were detected
