11 sonuçlar
Arama Sonuçları
Listeleniyor 1 - 10 / 11
Öğe Investigation of the usability of biodiesel obtained from residual frying oil in a diesel engine with thermal barrier coating(Journals & Books, 2015-04-05) Aydın, Hüseyin; Sayın, Cenk; Aydın, SelmanIn this study, biofuel was produced from residual frying oil of cottonseed and D2, B5 and B100 fuels were prepared in order to use in experiments. These fuels were tested in a single cylinder, four strokes, 3 LD 510 model Lombardini CI engine. Then the top surfaces of the piston and valves were coated with plasma spray coating method by using 100 μm of NiCrAl as lining layer and over this layer the same surfaces were coated with 400 μm of the mixture that consists of %88 ZrO2, %4 MgO and %8 Al2O3. After the coating process, above mentioned fuels were tested in the coated engine. Previously, same fuels had been tested in uncoated engine, at full load and various speeds. Performance, emission and combustion experiments were carried out in coated engine. By coating process, partial increases were observed in power, exhaust manifold temperature and engine noise, while partial decreases were seen in brake specific fuel consumption (Bsfc). Besides, partial reductions were found in carbon monoxide (CO), hydrocarbon (HC) and smoke opacity emissions, but partial increases were observed in nitrogen oxide (NOx) emissions. Cylinder gas pressure values were higher for coated engine. Moreover, heat releases were close to each other in both engines.Öğe An analysis of biodiesel requirement, production and policies in Turkey(e-Journal of New World Sciences Academy, 2008-02-01) Aydın, Hüseyin; Bayındır, HasanThe development of alternative fuels from renewable resources, like biomass, has gained considerable attention in recent years. A biodiesel program would give many benefits in terms of generation of employment for poor/rural people, farmers, accelerate of starting many type of industries for developing countries like Turkey. This paper investigates current status of biodiesel in Turkey, advantages and disadvantages of biodiesel in diesel engines, annual diesel fuel consumption, import and export ratings and annual diesel fuel demand. The main focus of this paper is on Turkey’s current fuel status and to clarify Turkey’s biodiesel demand as alternative to fossil diesel fuel. Results show that Turkey is highly in need of alternative energies such as bio-fuels. That’s way it is recommended that Turkey should promote oilseed crops farming to the rise production of biodiesel.Öğe Performance and emission evaluation of a CI engine fueled with preheated raw rapeseed oil (RRO)–diesel blends(Journals & Books, 2010-03) Aydın, Hüseyin; Hanbey, HazarMany studies are still being carried out to find out surplus information about how vegetable based oils can efficiently be used in compression ignition engines. Raw rapeseed oil (RRO) was used as blended with diesel fuel (DF) by 50% oil–50% diesel fuel in volume (O50) also as blended with diesel fuel by 20% oil–80% diesel fuel in volume (O20). The test fuels were used in a single cylinder, four stroke, naturally aspirated, direct injection compression ignition engine. The effects of fuel preheating to 100 °C on the engine performance and emission characteristics of a CI engine fueled with rapeseed oil diesel blends were clarified. Results showed that preheating of RRO was lowered RRO’s viscosity and provided smooth fuel flow Heating is necessary for smooth flow and to avoid fuel filter clogging. It can be achieved by heating RRO to 100 °C. It can also be concluded that preheating of the fuel have some positive effects on engine performance and emissions when operating with vegetable oil.Öğe Determination of performance and exhaust emissions properties of B75 in a CI engine application(Journals & Books, 2011-09) Aydın, Hüseyin; İlkılıç, CumaliIn this study, performance and exhaust emissions of biodiesel in a compression ignition engine was experimentally investigated. Therefore, biodiesel has been made by transesterification from cotton seed oil and then it was mixed with diesel fuel by 25% volumetrically, called here as B75 fuel. B75 fuel was tested, as alternative fuel, in a single cylinder, four strokes, and air-cooled diesel engine. The effect of B75 and diesel fuels on the engine power, engine torque and break specific fuel consumption were clarified by the performance tests. The influences of B75 fuel on CO, HC, NOx, Smoke opacity, CO2, and O2 emissions were investigated by emission tests. The engine torque and power, for B75 fuel, were lower than that of diesel fuel in range of 2–3%. However, for the B75, specific fuel consumption was higher than that of diesel fuel by approximately 3%. CO2, CO, HC, smoke opacity and NOx emissions of B75 fuel were lower than that of diesel fuel. The experimental results showed that B75 fuel can be substituted for the diesel fuel without any modifications in diesel engines.Öğe Analysis of combustion characteristics of a LHR-STD diesel engine fuelled with biofuel and diesel fuel((SSRG-IJTE), 2017-04) Aydın, Hüseyin; Aydın, Selman; Sayın, Cenk; Yakut, RıfatIt is important to efficiently use of alternative fuel in CI (compression ignition) engine, because of the lack of energy shortages will be in the present and coming years. Therefore this study, the top surfaces of the piston, exhaust and inlet valves of a four-stroke, direct injection, single cylinder CI engine was coated with a mixture of insulation materials by use of plasma spray method. After that, determine of combustion characteristics of standard (STD) CI engine and the low heat rejection (LHR) CI engine were tested under the same experimental conditions and the same experimental setup, fuelled with the WB20, WB100 and DF fuels. The results of both engines are compared with each other so that analyze how this modification is effect on the combustion parameters. Experimental results showed that LHR diesel engine generally is partly similar to STD diesel engine in terms of the knock density, mass burning rate, average gas temperature, velocity of heat transfer, coefficient of heat transfer and total heat transfer.Öğe Investigation of the effects of butanol addition on safflower biodiesel usage as fuel in a generator diesel engine(Elsevier, 2018-06-15) Aydın, Hüseyin; Çelebi, YahyaAs our world demands more and more energy and fossil fuel resources are running out, searches onfindingalternative fuels in internal combustion engines are increasing. Alcohols and biofuels obtained from oils can beused as alternative diesel fuels. The present work investigated the effects ofn-butanol addition to safflowerbiodiesel usage in a diesel engine used for driving an electrical power generator. Safflower biodiesel was ob-tained by using transesterification method. Binary blends of butanol-biodiesel and ternary blends of ultra-lowsulfur diesel-biodiesel–butanol were contained 5%, 10%, and 20% butanol in volume basis. The tests werecarried out on a four-cylinder, four-strokes, and direct-injection diesel engine at half load operation with stableengine speed of 1500 rpm. Experimental test results on combustion characteristics, emission and performance ofthe fuels were investigated. According to test results, formation of heat release rates and in-cylinder pressurecurves were considerably similar and total heat transfer, average gas temperature and mass fraction burned wereslightly changed. The ternary blends showed lower emission and increased brake thermal efficiency up to 1.5%.Besides, average mass fuel consumption was increased up to 5% and brake specific fuel consumption up to 6%.For the other fuels, emission and brake thermal efficiency were deteriorated.Öğe Usage of methyl ester produced from waste grape and Mn additive as alternative diesel fuel(Petru Maior” University of Tîrgu Mureş, 2017-01) Aydın, Hüseyin; Hanbey, Hazar; Uyar, Mahmut; Sap, EmineIn this study, methyl ester was produced from waste grape pulp sources. The produced methyl ester was mixed with diesel in different proportions, and was tested for engine performance and emission. It was found that with increasing biodiesel content, the specific fuel consumption and exhaust temperature have increased partially, while the CO, HC and smoke emissions decreased significantly. Additionally, in the scope of this study, dodecanol, propylene glycol and Mn based additives were added to fuel B50 to improve the emission and engine performance values. With the presence of additives, an increase in the exhaust temperature was observed, while a decrease in the specific fuel consumption, CO, HC, and smoke emissions were detectedÖğe Terebinth oil for biodiesel production and its diesel engine application(Journals & Books, 2015-08) Aydın, Hüseyin; İlkılıç, Cumali; Çılğın, ErdalIn this study, biodiesel was produced from terebinth oil by the well known transesterification process in the methyl alcohol environment. Terebinth is non-edible oil, thus food versus fuel conflict will not arise if this is used for biodiesel production. The optimum conditions of transesterification process for biodiesel production are investigated in this study. A maximum of 77% biodiesel was produced with 20% methanol in presence of 1% sulphuric acid (H2SO4). The resulting biodiesel is quite similar to conventional diesel fuel in its main characteristics. The obtained biodiesel from terebinth oil was added to diesel fuel volumetrically by 10% and 50%. The fuel mixtures that obtained from the addition of 10% and 50% of biodiesel were named here as B10 fuel and B50 fuel. Performance and exhaust emissions of biodiesel in a compression ignition engine were experimentally investigated. Biodiesel blends have lowered power output with increased brake specific fuel consumption (Bsfc) probably due to the lower heating value of biodiesel. The engine experimental results showed that exhaust emissions including carbon monoxide (CO), carbon dioxide (CO2), and hydrocarbons (HC) were reduced for all biodiesel fuel mixtures. However, a slight increase in oxides of nitrogen (NOx) emission was experienced for biodiesel mixtures.Öğe Fuel production from waste vehicle tires by catalytic pyrolysis and its application in a diesel engine(Journals & Books, 2011-05) Aydın, Hüseyin; İlkılıç, CumaliAn alternative fuel production was performed by pyrolysis of waste vehicle tires under nitrogen (N2) environment and with calcium hydroxide (Ca(OH)2) as catalyst. The sulfur content of liquids obtained were reduced by using Ca(OH)2. The liquid fuel of waste vehicle tires(TF) was then used in a diesel engine to blend with petroleum diesel fuel by 5%(TF5), 10%(TF10), 15%(TF15), 25%(TF25), 35%(TF35), 50%(TF50), and 75%(TF75) wt. and pure (TF100). Performance characteristics such as engine power, engine torque, brake specific fuel consumption (bsfc) and exhaust temperature and emission parameters such as oxides of nitrogen (NOx), carbon monoxides (CO), total unburned hydrocarbon (HC), sulfur dioxides (SO2) and smoke opacity of the engine operation with TF and blend fuels of TF–diesel were experimentally investigated and compared with those of petroleum diesel fuel. It was concluded that the blends of pyrolysis oil of waste tires TF5, TF10, TF25 and TF35 can efficiently be used in diesel engines without any engine modifications. However, the blends of TF50, TF75 and TF100 resulted considerably to high CO, HC, SO2 and smoke emissions.Öğe Combustion, performance, and emissions of safflower biodiesel with dimethyl ether addition in a power generator diesel engine(Taylor & Francis, 2020-04-29) Aydın, Hüseyin; Işık, Mehmet Zerrakki; İşcan, Bahattin; Topkaya, HüsnaIn this study, the effect of dimethyl ether (DME) addition to diesel (ultralow sulfur diesel fuel) and biodiesel fuels on the combustion, performance, and emissions of a diesel-powered generator was investigated. For this purpose, fuel samples of the ternary blend that volumetrically composed of 10% safflower biodiesel–10% dimethyl ether–80% ultralow sulfur diesel fuel (B10DME10), the ternary blend that volumetrically composed of 25% safflower biodiesel–25% dimethyl ether–50% ultralow sulfur diesel fuel (B25DME25), the binary blend that volumetrically composed of 25% safflower biodiesel–75% ultralow sulfur diesel fuel (B10DME10) B25, and pure safflower oil biodiesel (B100) and standard ultralow sulfur diesel (D2) were prepared. The test engine was loaded by power drawing from the generator by the usage of equivalent powered electrical heating resistances. Generally, using DME with biodiesel improved the combustion properties of biodiesel blends that can be attributed to the lower viscosity of DME. The maximum cylinder pressure was obtained for B10DME10 in general and sometimes for B25DME25. When test fuels are compared, DME blends showed higher and earlier peaks of heat release compared to diesel and biodiesel blend fuels especially. It was found that combustion is more efficient from mass fuel consumption (MFC) and brake specific fuel consumption (BSFC) values in the use of DME than biodiesel. BSEC values of using DME in the blends considerably decreased that it is the proof of improved combustion and energy efficiency. The highest average efficiency values were obtained for B25DME25 as 28.3% although it has a lower calorific value than D2 due to the considerably improved combustion properties of DME, while the average efficiency values were 23.1%, 23.3%, and 20.7% for D2, B25, and B100 fuels, respectively. Highest carbon monoxide (CO) emissions were obtained in the use of pure biodiesel, while the lowest CO emissions were obtained in the use of DME. The addition of DME is seen to increase the nitrogen oxides (NOx) and CO emissions.
